Configuration example, Configuring wfq queuing, Configuration procedure – H3C Technologies H3C S6300 Series Switches User Manual
Page 57
47
Step Command
Remarks
1.
Enter system view.
system-view N/A
2.
Enter Ethernet interface
view.
interface interface-type
interface-number
N/A
3.
Enable byte-count or
packet-based WRR
queuing.
qos wrr { byte-count | weight } By default, byte-count WRR queuing is used.
4.
Assign a queue to a
WRR group, and
configure scheduling
parameters for the
queue.
qos wrr queue-id group { 1 |
2 } { byte-count | weight }
schedule-value
Select weight or byte-count according to the
WRR type (byte-count or packet-based) you
have enabled.
By default, all queues are in group 1, and the
weights of queues 0 through 7 are 1, 2, 3, 4,
5, 9, 13, and 15, respectively.
Configuration example
1.
Network requirements
Enable packet-based WRR on port Ten-GigabitEthernet 1/0/1, assign queues 0 through 3 to WRR
group 1, with their weights being 1, 2, 4, 6, respectively, and assign queues 4 through 7 to WRR
group 2, with their weights being 1, 2, 4, 6, respectively.
2.
Configuration procedure
# Enter system view.
# Configure WRR queuing on Ten-GigabitEthernet 1/0/1.
[Sysname] interface Ten-GigabitEthernet 1/0/1
[Sysname-Ten-GigabitEthernet1/0/1] qos wrr weight
[Sysname-Ten-GigabitEthernet1/0/1] qos wrr 0 group 1 weight 1
[Sysname-Ten-GigabitEthernet1/0/1] qos wrr 1 group 1 weight 2
[Sysname-Ten-GigabitEthernet1/0/1] qos wrr 2 group 1 weight 4
[Sysname-Ten-GigabitEthernet1/0/1] qos wrr 3 group 1 weight 6
[Sysname-Ten-GigabitEthernet1/0/1] qos wrr 4 group 2 weight 1
[Sysname-Ten-GigabitEthernet1/0/1] qos wrr 5 group 2 weight 2
[Sysname-Ten-GigabitEthernet1/0/1] qos wrr 6 group 2 weight 4
[Sysname-Ten-GigabitEthernet1/0/1] qos wrr 7 group 2 weight 6
Configuring WFQ queuing
Configuration procedure
To configure WFQ queuing:
Step Command
Remarks
1.
Enter system view.
system-view N/A
2.
Enter Ethernet interface view.
interface interface-type
interface-number
N/A
3.
Enable byte-count or
packet-based WFQ queuing.
qos wfq { byte-count |
weight }
The default queuing algorithm on an
interface is WRR queuing.
- H3C S5820V2 Series Switches H3C S5830 Series Switches H3C S5830V2 Series Switches H3C S3600V2 Series Switches H3C S6800 Series Switches H3C S3100V2 Series Switches H3C S12500-X Series Switches H3C S5560 Series Switches H3C WX6000 Series Access Controllers H3C WX5000 Series Access Controllers H3C WX3000 Series Unified Switches H3C LSWM1WCM10 Access Controller Module H3C LSWM1WCM20 Access Controller Module H3C LSQM1WCMB0 Access Controller Module H3C LSRM1WCM2A1 Access Controller Module H3C LSBM1WCM2A0 Access Controller Module H3C S9800 Series Switches H3C S5130 Series Switches H3C S5120 Series Switches