Marantz SR5004 - Manual (Page 78)

NAMES AND FUNCTIONS
76
BASIC
CONNECTIONS
BASIC
OPERA
TION
ADV
ANCED
CONNECTIONS
SETUP
ADV
ANCED
OPERA
TION
TROUBLESHOOTING
OTHERS
ADV
ANCED
OPERA
TION
ENGLISH
ADVANCED OPERATION
SR5004 REMOTE CONTROLLER
BASIC OPERATION
NORMAL MODE
(When operating Marantz AV equipment
products)
This remote controller is preset with a total of 12
types of remote codes, including Marantz BD, DVD,
VCR (VCR deck), DSS (Satellite broadcasting tuner),
TV (Television), CD, CDR, AUX, TUNER, USB, M-XP
and AMP mode.
Learning is not necessary for Marantz products. You
can use these products without setting any codes.
1.
Press the SOURCE button.
For this example, press DVD.
Pressing the SOURCE button once changes
the remote control to the settings for the
source that was pressed.
To change the amplifi er on other source,
press the SOURCE button twice (double-
click). The code is sent, and then the
amplifi er source changes to DVD.
SETTING THE BACK LIGHT
Pressing the Light button located on the side of
the remote controller lights the remote controller’s
backlight. Pressing the button again while the
backlight is lit lights the backlight for another 2
seconds.
To turn off back light, press and hold down the SET
and OFF button until SEND indicator blinks twice.
To turn on it again, press and hold down the SET and
ON button until SEND indicator blinks twice.
Initial is back light ON.
PRESET MODE
( W h e n o p e r a t i n g n o n - M a r a n t z AV
equipment products)
This remote controller is preset with remote control
codes from AV equipment by other manufacturers.
The preset codes are TV, CD, DVD and DSS.
Settings can be made in one of two ways.
When the preset codes are set, the following codes
are contained in the source button of the remote
controller.
See the attached manufacturer number list for the
preset manufacturers, devices, preset numbers,
and other settings.
Remote
controller
source name
Corresponding
preset code
Device name
TV TV Television
DVD DVD DVD player
CD CD CD player
DSS SATELLITE
Satellite
broadcasting
tuner equipment
BD BD
Blu-ray disc
player
Importants
• Some codes may be not match your equipment.
In this case, you can use LEARN mode to store
these codes.
• The preset codes do not cover full functions.
If you need extra function, use LEARN mode to
store extra function.
• Wen the batteries are getting weak, the preset
procedure is not successful.
PROGRAMMING WITH THE 4-DIGIT CODE
1.
1.
2.
1. Press and hold down the SOURCE button for
the appliance which should be controlled and
press SET button until the SEND indicator
blinks twice. Then back light fl ushes.
2.
Press the 4-digit code by numeric buttons
for appliance (code table at the end of this
book)
When the procedure is successful, the
SEND indicator will blink twice.
Note
If the indicator did not blink twice, then repeat steps
1 through 2 and try entering the same code again.
SCANNING THE CODE TABLE
2.
3.
5.
2.
3.
1.
Switch on the appliance which should be
controlled.
2.
Press and hold down the SOURCE button
for appliance which should be controlled
and press SET button until the SEND
indicator blinking twice. Then back light
fl ushes.
3.
Aim the remote control at the appliance
and slowly alternate between pressing
INPUT
3 button and the SOURCE ON/OFF
button for the appliance.
4.
Stop when the appliance turns off.
5.
Press ENTER button once to lock in the
code.
CHECKING THE CODE
1.
2.
4.
3.
1.
1. Press and hold down the SOURCE button
for appliance which should be controlled
and press SET button until the SEND
indicator blinking twice then back light
fl ushes.
2. Press the INFO button.
The SEND indicator will blink twice.
3. To view the code for first digit, press 1
once.
Count the SEND indicator blinks (e.g. 3
blinks = 3) and write down the number.
4.
Then press 2 to check the second digit of
the code. Now press 3 and 4 to check the
third and fourth digits of the code.
Note
If a code digit is “0”, the SEND indicator will not
blink.
RESETTING THE CODE
1.
1.
2.
1. Press and hold down the SOURCE button
for appliance which should be controlled
and press SET button until the SEND
indicator blinking twice.
Then back light fl ushes.
2. Press the below codes to reset.
TV : 1000
DVD : 2000
CD : 3000
DSS : 4000
BD : 5000
The indicator will blink twice.
Note
After this procedure, the selected SOURCE button
is set initial code.