Marantz SR5004 - Manual (Page 10)

NAMES AND FUNCTIONS
8
BASIC
CONNECTIONS
BASIC
OPERA
TION
ADV
ANCED
CONNECTIONS
SETUP
ADV
ANCED
OPERA
TION
TROUBLESHOOTING
OTHERS
NAMES AND FUNCTIONS
ENGLISH
8/NIGHT button
Pressing this button prevents the Dolby Digital
signal from playback at a loud voice.
When this button is pressed, the “NIGHT” indicator
is illuminated.
9/D.EQ/VOL buton
This button is used to select Audyssey Dynamic
EQ/Dynamic Volume modes.
0/CH SEL button
This button is used to call up CH LEVEL ADJUST
and adjust speaker levels or 7.1 ch input level.
+10/V.OFF button
This button is used to turn off the video signal.
¤1 M (MACRO) button (SR6004)
This button is used to program Macros. Pressing
this button switches between Normal mode and
Macro mode.
HT-EQ button (SR5004)
This button is used to turn on or off HT (Home
Theater)-EQ mode.
¤2 MENU button
(When AMP mode is selected)
This button is used to call up the SETUP MAIN
MENU of the unit.
(When USB mode is selected)
Pressing this button during iPod operation moves
you to higher-level page.
¤3 TOP button
(When AMP mode is selected)
Pressing this button during setup returns you to the
top screen of the setup main menu.
(When USB mode is selected)
Pressing this button displays the highest-level
item.
¤4 DISPLAY button
(When a mode other than USB is selected)
This button is used to selects the display mode for
the front display of the unit.
(When USB mode is selected)
This button is used to select the previous page.
¤5 INPUT 3 button
This button is for forward-feeding the input source
to select a desired source.
INPUT 4 button
This button is for backward-feeding the input source
to select a desired source.
¤6 SETUP/MODE button
This button is used to setup for DVD and other
device.
(When USB mode is selected)
This buttong is used to switch between direct/
remote mode during iPod opetation.
¤7 SOURCE button
These buttons are used to switch the source of your
A/V Receiver. Each time a source button is pressed,
the remote controller changes to the source which
was pressed.
This remote controller can control 12 types of
equipment. To change the A/V Receiver source,
press this button twice within two seconds. The
signal is sent when it is pressed the second time.
Notes
• Select the AMP as the source to use this remote
controller with the unit.
• In the case of SR5004, the USB button cannot be
used.
NAMES AND FUNCTION
¤8 ATT button
When the input signal is too high and the voice
distorts even by throttling the unit VOLUME control,
turn on this function.
“ATT” is indicated when this function is activated.
The input level reduced. Attenuator is invalid for the
output signal of “REC OUT”.
Note
This function is unavailable while the digital input
is selected.
¤9 A/D button
This button is used to switch between the analog
and digital inputs.
‹0 HDMI button (SR6004)
This button is used to select HDMI OUTPUT 1 or
2.
‹1 SET button
This button is used to enter learn mode and preset
mode.
‹2 I / SOURCE ON/OFF button
This button is used to turn a specifi c source (such
as a DVD player) on or off independently from the
rest of the system.
‹3 Infrared transmitter and learning
sensor
This transmitter emits infrared light. Press the
buttons while pointing the transmitter towards
the infrared receiver window of the unit or other
AV equipment. Be sure to also point towards
other remote controllers when using the learning
function.
SR6004
‹4 ‹5 ‹7 ‹6
‹4 LEARN indicator
This indicator is displayed when the remote
controller is in the LEARN mode.
‹5 MACRO indicator
This is displayed when a macro program is selected
by the remote controller.
‹6 Information indicator
Information about the sources and modes are
shown on the LCD.
‹7 indicator
This indicator is displayed when the remote
controller is transmitting a signal.
SR5004
‹8 SEND indicator
Indicates when the remote controller is transmitting
a signal.
‹9 LEARN indicator
Indicates when the remote controller is in the
LEARN mode.