Marantz SR5004 - Manual (Page 67)

NAMES AND FUNCTIONS
65
BASIC
CONNECTIONS
BASIC
OPERA
TION
ADV
ANCED
CONNECTIONS
SETUP
ADV
ANCED
OPERA
TION
TROUBLESHOOTING
OTHERS
ADV
ANCED
OPERA
TION
ENGLISH
ADVANCED OPERATION
ZONE SYSTEM
The ZONE System mode allows the same source
or different sources to be heard in two ZONEs other
than where this unit is installed.
To use the ZONE system, connect the audio from
the ZONE OUT A and B AUDIO output terminals to
the ZONE A and B amps.
If a surround back channel speaker or speaker C
(see page 21) are not used in the ZONE where this
unit is installed, the ZONE speaker system can be
used with the amp for the surround back channel.
This unit supports ZONE system functions such
as source selectors, ZONE speaker output, sleep
timers and remote control.
The unit shown in the illustrations is SR6004.
ZONE PLAYBACK USING THE ZONE OUT
TERMINALS
3. 4.
1.
5.
3.
5.
4.
1. Press the ZONE A or B button on the
remote controller.
2. When the ZONE setting mode is engaged,
one of the following screens appears on the
display for 10 seconds.
* Display when ZONE A is selected
Z A D V D - 1 8 d B
* Display when ZONE B is selected
Z B D V D ( D 2 )
3. Select the input source using the INPUT
SELECTOR knob on the unit or the function
button on the remote controller.
4.
Set the ZONE volume to be used by the
ZONE system to taste either by turning the
VOLUME knob on the unit or by pressing
the VOLUME +/– buttons on the remote
controller.
5. To cancel this function, press the ZONE A
or B button on the remote controller (after
pressing the AMP button on the remote
controller).
“MULTI” indicator on the front panel will
be turned off.
Notes
• In ZONE A, it is impossible to use HDMI or
digital input (optically or coaxially connected)
sources.
In ZONE B, it is possible to use only digital input
(optically and coaxially connected) sources.
• The sleep timer, monaural output and other
features can also be set using the MAIN MENU.
(See page 36)
• The volume for ZONE B cannot be set on the unit.
Control the volume by adjusting it on the amp
connected to ZONE B OUT.
• When component video output is not being used
in the main ZONE, it can be used for ZONE A
instead. Refer to page 35. (SR6004 only)
ZONE PLAYBACK USING THE ZONE
SPEAKER A TERMINALS
This unit allows you to connect another set of
speakers amp and place them in a different ZONE
or separated area for Iistening to music.
3. 4.
1.
5.
3.
5.
4.
1. Press the ZONE SPEAKER (Z.SPKR) button
on the remote controller.
2. When the ZONE SPEAKER setting mode
is engaged, one of the following screens
appears on the display for 10 seconds.
* Display when ZONE SPEAKER A is selected
Z S A D V D - 1 8 d B
3.
Select the input source using the INPUT
SELECTOR knob on the unit or the function
button on the remote controller.
4.
Set the ZONE volume to be used by the
ZONE system to your own preference,
either by turning the VOLUME knob on
the main unit or by pressing the VOLUME
+/– buttons on the remote controller.
5. To cancel this function, press the Z.SPKR
button on the remote controller (after
pressing the AMP button on the remote
controller).
“MULTI” indicator on the front panel will
be turned off.
Notes
• Digital input (optically and coaxially connected)
sources cannot be used for ZONE speaker A.
• The sleep timer, monaural output and other
features can also be set using the MAIN MENU.
(See page 36.)
Notes for ZONE Speaker
• The ZONE Speaker mode can be set for only one
of the ZONE A.
• The ZONE SPEAKER output can be used when
Surround Back Speaker = “None, Zone SPKR”
in the SPEAKER SETUP menu. (See SPEAKER
SETUP, page 31)
• “Check! Height or Surr Back Speakers” is
displayed when the ZONE SPEAKER button is
pressed when the Surround Back Speaker is not
set to “None, Zone SPKR” in the SPEAKER
SETUP menu. (See SPEAKER SETUP, page 31)
• The ZONE speaker mode cannot be used at the
same time as the speaker C. When connecting for
ZONE use, set the SPEAKER C selector switch
on the rear panel to OFF.
• When the unit is put in ZONE SPEAKER mode and
ZSP A has been set as the Surround Back or Front
Height Speaker (page 31), the ZONE SPEAKER
function can be turned on automatically simply by
pressing the SOURCE button.