Comtech EF Data LPOD - Manual (Page 26)

LPOD C-, X-, or Ku-Band Outdoor Amplifier / Block Up Converter (BUC) MN-LPOD
Introduction Revision 10
1–8
1.5 Summary of Specifications
1.5.1 Characteristics
IF Input Frequency Note 1 RF Output Frequency
950 – 1525 MHz 5.850 – 6.425 GHz
950 – 1750 MHz 5.850 – 6.650 GHz (optional)
950 – 1825 MHz 5.850 – 6.725 GHz (optional)
965 – 1265 MHz 6.725 – 7.025 GHz
950 – 1450 MHz 7.900 – 8.400 GHz
950 – 1450 MHz 14.00 – 14.50 GHz
950 – 1750 MHz 13.75 – 14.50 GHz (optional)
Model Psat (Typical) P1dB (Guaranteed) Note 2
PS1-25C,X 44 dBm (25 W) 43 dBm (20 W)
PS1-32C,X 45 dBm (32 W) 44 dBm (25 W)
PS1-40C,X 46 dBm (40 W) 45 dBm (32 W)
PS1-50C,X 47 dBm (50 W) 46 dBm (40 W)
PS1-60C,X 48 dBm (60 W) 47 dBm (50 W)
PS1-20Ku 43 dBm (20 W) 42 dBm (16 W)
PS1-32Ku 45 dBm (32 W) 44 dBm (25 W)
PS1-40Ku 46 dBm (40 W) 45 dBm (32 W)
PS1.5-75C,X 48.6 dBm (75 W) 48 dBm (60 W)
PS1.5-80C,X 49 dBm (80 W) 48.5 dBm (70 W)
PS1.5-100C,X 50 dBm (100 W) 49 dBm (80 W)
PS1.5-110C,X 50.4 dBm (110 W) 49.5 dBm (90 W)
PS1.5 or PS2-125C,X 51 dBm (125 W) 50 dBm (100 W)
PS1.5-50Ku 47 dBm (50 W) 46 dBm (40 W)
PS1.5-60Ku 48 dBm (60 W) 47 dBm (50 W)
PS2-150C,X 51.8 dBm (150 W) 51 dBm (125 W)
PS2-200C,X 53 dBm (200 W) 52.5 dBm (175 W)
PS2-250C,X 54 dBm (250 W) 53 dBm (200 W)
PS2-100Ku 50 dBm (100 W) 49 dBm (80 W)
PS2-125Ku 51 dBm (125 W) 50 dBm (100 W)
Notes:
1. PS 2 Models available as SSPAs only, without internal L-Band BUC (Freq RF in = Freq RF out).
2. Allow 1 dB degradation from 13.75 to 14.0 GHz and 6425 to 6725 MHz.
Gain Min (Typical) 70 (75 dB)
Input Power Supply Requirements
90-264 VAC, 47-63 Hz, Power Factor Corrected, .96 (typical)
(48 VDC optional)
Max IF Input level (no damage) +10 dBm
Gain Adjust 20 dB in 0.25 dB steps
Gain Flatness
± 1.5 dB full band (optional ± 2.0 dB full band (-50° to +55°C))
± 0.30 dB per 40 MHz (optional ± 0.50 dB per 40 MHz (-50° to
+55°C)
Gain variation over temp
±1.5 dB max, -40° to +55°C (optional ± 2.0 dB max (-50° to
+55°C))