Adtec digital RD-70 (version 1.02.04) Manual - Manual (Page 16)

configurations.
LNB Polarity This control is primarily used in “Universal” LNB
applications. The LNB Polarity control allows for
LNB polarization selection; the 13VDC source will
select the Vertical polarity and the 18VDC source
will select the horizontal polarity. For typical “C”
and “Ku” band applications, the 18 VDC option is
recommended.
H(18V)
V(13V)
LNB Tone This control is used only for Universal LNB
applications. A universal LNB can route the high
or low band from either polarity to the IRD. The
high band is selected by enabling the 22 kHz
tone and the low band is selected when the 0 Hz
tone is enabled.
0KHz
22KHz
Profile
Menu
Save Allows user to save currently running RF
configuration to a profile. Press then
use keypad for custom name entry. Press to confirm name and save profile.SelectAllows user to load profile from list. Press then and arrows to list
profiles. press to load selected profile.
to confirm name and save profile.
Select Allows user to load profile from list. Press
Delete Allows user to delete profile from list. Press
then and arrows to list profiles. press to delete selected
profile.RF Rx Menu (LB L-Band)ItemFunctionOptionsTuner StateEnables or Disables RF input. note: When RF1 and RF2 are both enabled,
maximum tuner performance is affected. Please view table in Appendix A for symbol rate and modcod resource limitations.DISABLEDENABLEDDownlinkAllows the operator to enter the satellite
downlink frequency. The value for the Downlink frequency is used with the Local Oscillator
frequency to calculate the L-Band frequency. TheDownlink and Local Oscillator frequencies can be
used to determine if spectrum inversion occurs using the following rules. If the Downlink
frequency is less than the Local Oscillator frequency, then spectrum inversion does occur. Range dependent upon LO
configuration Pages: 1 … 14 15 16 17 18 … 68 wrong Brand wrong Model non readable This manual is related to the following products: signEdje (version 02.07.09) Quick Start mediaHUB-HD 422 (version 1.01.10_M_2) Quick Start mediaHUB-HD Pro (version 03.07.19) Quick Start YUV2QAM (version 01.02.01) Quick Start EN-30 (version 1.02.02) Quick Start EN-81 (version 2.02.28) Manual EN-80 (version 2.02.28) Manual EN-100 (version 2.00.31) Manual EN-91 / EN-91P (version 1.02.29) Manual RD-60 (version 1.13.02) Manual See also other documents in the category Adtec digital Video: DPI-1200 (version 01.04.08U) Quick Start (2 pages) DPI-1200 (version 01.04.08U) Manual (58 pages) mediaHUB-HD 422 (version 1.01.10_M_2) Quick Start (2 pages) mediaHUB-HD 422 (version 1.01.10_M_2) Quick Start (67 pages) mediaHUB-HD 422 (version 1.01.10_M_2) Quick Start (2 pages) mediaHUB-HD 422 (version 1.01.10_M_2) Quick Start (2 pages) EN-80 (version 2.02.28) Quick Start (2 pages) EN-30 (version 1.02.02) Manual (59 pages) RD-30 (version 2.1.1) Quick Start (1 page) RD-30 (version 2.1.1) Manual (39 pages) mediaHUB-HD 422 (version 1.01.10_M_2) Quick Start (2 pages) mediaHUB-HD 422 (version 1.01.10_M_2) Quick Start (2 pages) mediaHUB-HD 422 (version 1.01.10_M_2) Quick Start (2 pages) YUV2QAM (version 01.02.01) Manual (46 pages) Soloist-HD Pro (version 02.07.09) Manual (77 pages) EN-91 / EN-91P (version 1.02.29) Quick Start (2 pages) DTA-3050 (version 6.02.14) Manual (94 pages) EN-20 (version 2.03.06) Manual (63 pages) mediaHUB-HD Pro (version 03.07.19) Studio Encoder Quick Start (2 pages) RD-60 (version 1.13.02) Quick Start (2 pages) edje-5110 (version 01.02.05) Manual (98 pages) eyeMonitor (42 pages) TBGS w/adManage (50 pages) Soloist 4111 (version 02.07.03) (1 page) EN-40 (version 2.02.24) (2 pages) mediaHUB (version 02.00.13) (24 pages) edje-5110 (version 01.02.05) Quick Start (2 pages) MAS & iptvManage (44 pages) AVS2 (5 pages) mediaHUB-HD 422 (version 1.01.10_M_2) Manual (104 pages) Sitemap
profiles. press to delete selected
profile.
RF Rx Menu (LB L-Band)
Item Function Options
Tuner State Enables or Disables RF input.
note: When RF1 and RF2 are both enabled,
maximum tuner performance is affected. Please
view table in Appendix A for symbol rate and
modcod resource limitations.
DISABLED
ENABLED
Downlink Allows the operator to enter the satellite
downlink frequency. The value for the Downlink
frequency is used with the Local Oscillator
frequency to calculate the L-Band frequency. The
Downlink and Local Oscillator frequencies can be
used to determine if spectrum inversion occurs
using the following rules. If the Downlink
frequency is less than the Local Oscillator
frequency, then spectrum inversion does occur.
Range dependent upon LO
configuration