Altera Transceiver Signal Integrity Development Kit, Stratix IV GT Edition - Manual (Page 15)

Chapter 2: Board Components 2–5
Featured Device: Stratix IV GT Device
November 2011 Altera Corporation Transceiver Signal Integrity Development Kit,
Stratix IV GT Edition Reference Manual
Featured Device: Stratix IV GT Device
The Stratix IV GT transceiver signal integrity development board features the
EP4S100G2F40I1N Stratix IV FPGA device (U33) in a 1517-pin FBGA package.
f
For more information about the Stratix IV GT devices, refer to the Stratix IV Device
Handbook .
J2 0.95-V banana jack
Banana jack for supplying external 0.95-V V
CC
power to the FPGA.
Fuses F1 and F2 must be removed prior to supplying external power to
this banana jack.
J3 VCCA banana jack
Banana jack for supplying external V
CCA
power to the FPGA. Fuse F3
must be removed prior to supplying external power to this banana jack.
J7 VCCR banana jack
Banana jack for supplying external V
CCR
power to the FPGA. Fuse F4
must be removed prior to supplying external power to this banana jack.
J8 VCCT banana jack
Banana jack for supplying external V
CCT
power to the FPGA. Fuse F5
must be removed prior to supplying external power to this banana jack.
J9 VCCH banana jack
Banana jack for supplying external V
CCH
power to the FPGA. Fuse F6
must be removed prior to supplying external power to this banana jack.
J10 VCCL banana jack
Banana jack for supplying external V
CCL
power to the FPGA. Fuse F7
must be removed prior to supplying external power to this banana jack.
J4 GND banana jack Banana jack connected to GND of the board.
F1, F2 10A fuse
Fuses for 0.95-V V
CC
core of the FPGA. These fuses must be removed
when an external power is applied to this banana jack.
F3 2A fuse
Fuse for V
CCA
power of the FPGA. This fuse must be removed when an
external power is applied to this banana jack.
F6 5A fuse
Fuse for V
CCH
power of the FPGA. This fuse must be removed when an
external power is applied to this banana jack.
F7 2A fuse
Fuse for V
CCL
power of the FPGA. This fuse must be removed when an
external power is applied to this banana jack.
F4 2A fuse
Fuse for V
CCR
power of the FPGA. This fuse must be removed when an
external power is applied to this banana jack.
F5 2A fuse
Fuse for V
CCT
power of the FPGA. This fuse must be removed when an
external power is applied to this banana jack.
U14 Power measurement ADC
Linear Technology LTC2418CGN 24-bit delta-sigma analog to digital
converter (ADC).
R3 0.001- Ω Rsense Sense resistor for measuring FPGA V
CC
core power.
R11 0.009- Ω Rsense Sense resistor for measuring FPGA V
CCA
power.
R24 0.009- Ω Rsense Sense resistor for measuring FPGA V
CCH
power.
R25 0.009- Ω Rsense Sense resistor for measuring FPGA V
CCL
power.
R20 0.009- Ω Rsense Sense resistor for measuring FPGA V
CCR
power.
R21 0.009- Ω Rsense Sense resistor for measuring FPGA V
CCT
power.
Table 2–1. Stratix IV GT Transceiver Signal Integrity Development Board Components (Part 4 of 4)
Board Reference Type Description