Presehing stations, To select a band with the remote control, To search for a station quickly (auto search) – Aiwa CX-NA30 User Manual
Page 8: When an fm stereo broadcast contains noise, To change the am tuning interval, Selecting a preset number on the main unit, To clear a preset station, Manual tuning presehing stations, Preset number tuning
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
RADIO RECEPTION
MANUAL TUNING
PRESEHING STATIONS
MONO/
TUNER
ooo
ooo
ooo
O Q
;:)oo
■0-9,+10
1 Press the TUNER/BAND button repeatedly to
select the desired band.
—► FM —►AM---------
If the power is turned off, the previously tuned station will be
played (Direct Play Function).
To select a band with the remote control
Press the BAND button while pressing the SFIIFT button.
Press the DOWN or UP button to select
a station.
Each time the button is pressed, the frequency changes.
When a station is received, “TUNE” is displayed for 2 seconds.
During FM stereo reception, (lissi)l is displayed.
/;
!
!
n ■■■■; n n
D D'U u
□
To search for a station quickly (Auto Search)
Keep the DOWN or ►M UP button pressed until the tuner
starts searching for a station. After tuning in to a station, the
search stops.
Tc stop the Auto Search manually, press the M-4 DOWN or
UP button.
• "he Auto Search may not stop at stations with very weak
signals.
When an FM stereo broadcast contains noise
Press the MONO TUNER button while pressing the SHIFT button
on the remote control so that “MONO” appears on the display.
Noise is reduced, although reception is monaural.
Tc> restore stereo reception, press these buttons so that MONO
disappears.
To change the AM tuning interval
The default setting of the AM tuning Interval is 10 kHz/step. If
you use this unit in an area where the frequency allocation system
is 9 kHz/step, change the tuning interval.
P'ess the POWER button while pressing the TUNER/BAND
button.
To reset the interval, repeat this procedure.
W hen the AM tuning interval is changed, all preset stations are
cleared. The preset stations have to be set again.
7
ENGLISH
The unit can store a total of 32 preset stations. (Each band has
a maximum of 20 available preset stations.) When a station is
stored, a preset number is assigned to the station. Use the preset
number to tune in to a preset station directly.
1 Press the TUNER/BAND button to select a band,
and press the DOWN or UP button to
select a station.
2 Press the II SET button to store the station.
A station is assigned a preset number, beginning from 1 in
consecutive order for each band.
Frequency
a.
!• .‘i
■ ;
[Cn n n n
.'.J
LJ
Preset number
3 Repeat steps 1 and 2.
The next station will not be stored if a total of 32 preset stations
for all the bands or a total of 20 preset stations for one band
have already been stored.
PRESET NUMBER TUNING
Use the remote control to select the preset number directly.
1 Press the BAND button whiie pressing the SHIFT
button to select a band.
2 Press the numbered buttons to select a preset
number.
Example:
To select preset number 20, press the +10, +10 and 0 buttons.
To select preset number 15, press the +10 and 5 buttons.
Selecting a preset number on the main unit
Press the TUNER/BAND button to select a band. Then, press
the ► PRESET button repeatedly.
Each time the button is pressed, the next highest number is
selected.
To clear a preset station
Select the preset number of the station to be cleared. Then, press
the ■ CLEAR button, and press the
II
SET button within 4
seconds.
The preset numbers of all other stations in the band with higher
numbers are also decreased by one.