Aiwa CX-NA30 - Manual (Page 15)

PROGRAMMED EDIT RECORDING
3
.
7
.
8.9
5
4,5
3
.
7
.
8.9
Programmed edit function enabies CD recording while checking
the remaining time on each side of the tape as the tracks are
programmed.
Repeat step 5 for the rest of the tracks for side A..
A track whose playing time is longer than the remaining time
cannot be programmed.
Remaining time
of side A
Total number
of programmed
tracks
Programmed
tracks
^OP -ivr , ,
ha :.*. ! ;
bi>
f";
L j '- L..; LJ
o
z
Q
CC
O
U
UJ
cr
Press the EDIT/CHECK button while pressing the
SHIFT button on the remote control to select side
B and program the tracks for side B.
After confirming B on the display, repeat step 5.
Tape side B (reverse side) .
The programmed edit recording will not start from a point halfway
in the tape. The tape must be recorded from the beginning of
either side.
1 Insert the tape into deck 2.
Insert the tape with the side to be recorded on first facing out
from the unit.
2 Press the CD button and load the disc(s).
3 Press the EDIT/CHECK button twice while
pressing the SHIFT button on the remote control.
“EDIT” and “PRGM” lights up on the display.
EDIT PRGM
: ! ! ; ! ! ■ ■ ! !
n ! 1 ! ! i
"n
j r : ;
4 Press the numbered buttons on the remote
control to designate the tape length.
10 to 99 minutes can be specified.
Tape length
Maximum recording
time for side A
n n ;■■■■■ ¡■•I !...... ;...............
i ; : f
O'-
■ ■ :
-L..'- LJ L.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I
Tape side A (front side)
5 Press the one of the DISC DIRECT PLAY buttons
to select a disc.
Then, press the numbered buttons and the + 10
button on the remote control to program a track.
Example: To select the 10th track of disc 2, press the DISC
DIRECT PLAY 2 button, then press the + 10 and 0 buttons.
8 Press the EDIT/CHECK button while pressing the
SHIFT button to select side A and press the #
REC/REC MUTE button to start recording.
CD play and recording of edited tracks for the first side start
simultaneously. When the last truck programmed for side A,
deck 2 enters the recording stop mode. After entering the
recording stop mode, go to step 9.
9 Press the EDIT/CHECK while pressing the SHIFT
button on the remote control for recording of
the second side.
B is displayed.
10 Turn over the tape in deck 2 and press the #
REC/REC MUTE button to start recording.
Recording starts.
To stop recording
Press the ■ button. Recording and CD play stop simultaneously.
To check the order of the programmed track numbers
Before recording, press the EDIT/CHECK button while pressing
the SHIFT button on the remote control to select side A or B, and
press the ◄◄ or ►► button repeatedly.
Program number
1
.............
■■■■■; I i r": ;■■■■■;
I
Track number Programmed
track numbers
To change the program of each side
Press the EDIT/CHECK button while pressing the SHIFT button
on the remote control to select side A or B, and press the 11
CLEAR button to clear the program of the selected side. Then
program tracks again.
To clear the edit program
Press the ■ button twice so that “EDIT” disappears on the
display.
'iMii
Recording is inhibited if the erasure prevention tab on either side
of the tape is broken off.
.
ENGLISH
14