Panasonic OMNIVISION PV-DM2791 - Manual (Page 60)

Settings for DVD Operation (continued)
AUDIO OUTPUT
Select the digital output to be output from the optical
digital audio output connector of the unit.
Do steps 1 and 2 on page 59.
DVD MAIN MENU
GUAGES
SELECT
SET
END
1) Press AT* to select
“AUDIO OUTPUT.”
2) Press SET to
display screen.
AUDIO OUTPUT
olby Dmiiat
dia :OFF
OftC :OPF
SURROUND : OFF
SELECT
SET
END
1) Press AT to select
an item.
2) Press SET
repeatedly for output.
(See below.)
■ “LPCM (DVD)” selections
OFF: Linear PCM of less than 48 kHz/16 bit is output.
When playing DVDs recorded in linear PCM of
over 48 kHz/20 bit or 96 kHz, no digital audio is
output. (Factory preset)
PCM: When playing DVDs recorded in linear PCM of
48 kHz/20 biV24 bit or 96 kHz, digital audio
converted to 48 kHz/16 bit is output.
(Digital output of PCM audio is restricted to
48 kHz/16 bit or below for copyright protection.)
■ “Dolby Digital” selections
Bitstream: Dolby Digital bitstream (1ch*5.1ch) is
output. (Factory preset)
OFF: No output.
■ “dts” selections
Bitstream: dts bitstream is output. (Factory preset)
OFF; No output.
■ “DRC (Dynamic Range Compression)” selections
OFF: Normal audio range is selected. (Factory preset)
ON: For dynamic sound even at low volume, this is
useful for late-night listening, [Dolby Digital DVDs
only].
■ “SURROUND” selections
Surround Sound creates the effect of sound coming from
non-existent rear speakers even when only connected to a
2-channel stereo system.
OFF: No Surround Sound effect. (Factory preset)
ON: Surround Sound effect.
4 Press ACTION to redisplay DVD menu
and go to step 2 to setup another item.
Or, press ACTION three times to exit.
Type of amplifier
to be connected
Recommended setting
LPCM
(DVD) Dolby
Digital
dts
No amplifier is connected OFF OFF OFF
AV amplifier (with digital
audio input connector)
without Dolby Digital/dts
decoder
PCM*1 0FF*2 0FF*2
AV amplifier including
Dolby Digital decoder
PCM*’ Bitstream OFF
AV amplifier including
Dolby Digital/dts decoder
PCM*' Bitstream Bitstream^
• Make settings according to amplifier connected
to optical audio output as shown in above table.
• When a dts decoder is not connected, to enjoy
dts DVD, please select audio output other than
dts at the dts DVD menu screen. Otherwise,
there will be no sound from the unit speakers.
*1 Audio output from unit is converted to 48 kHz/
16 bit in addition to audio from digital audio
output.
To enjoy high quality sound at 48 kHz/20 bit /
24 bit or 96 kHz, connect the amplifier or
decoder directly to the audio output
connectors, not to the digital audio output
connector, (Select “OFF’ at the “LPCM (DVD)”.j
*2 When connecting an amplifier (with an optical
digital input connector) which does not
contain the Dolby Digital or dts decoder, be
sure to select “OFP.
If “Bitstream” is selected, starting DVD play
may cause such a high level of noise as to be
harmful to your ears and damage the
speakers.
*3 When a dts decoder is connected, please
select “Bitstream’’ in “dts”. If “OFF” is
selected, there will be no sound.
• Turn off other surround effects when using this
surround effect.
• For optimum effect, the distance between the
unit and the listener should be about 3 or 4
times the distance between the right and left
front speakers.
60
For assistance, please call ; 1-800-211-PANA(7262) or send e-mail to : [email protected]