Banner DUO-TOUCH Run Bar with STB Buttons - Manual (Page 10)

Specifications
Power
Supply Voltage and Current: 10 to 30 V dc
Power Consumption: approx. 1.8 W @ 24 V dc (with no output load),
for each STB
Supply Protection Circuitry: Protected against transient voltages and
reverse polarity
Connections
Models STBVP6-RB1/-RB2 and -RB1E02/-RB2E02: Terminal strip
connections inside run bar housing (STBs are pre-wired). E-stop button
and EZ-LIGHT indicator (if used) are wired separately.
Models STBVP6-RB1Q8/-RB2Q8: 8-pin Mini-style quick-disconnect
fitting
Construction
STB Buttons: Totally encapsulated, non-metallic enclosure; black
polyetherimide yoke housing (see Application Note below); fiber-
reinforced polyester base; electronics fully epoxy-encapsulated.
E-Stop Button: Polyamide red button with metal base.
Run Bar Housing: 13 ga (0.090") cold rolled steel with powder coat
paint; polypropylene copolymer STB mount.
Ambient Light Immunity
Up to 100,000 lux
EMI/RFI Immunity
Immune to EMI and RFI noise sources, per IEC 947-5-2.
Application Notes
The STB’s polyetherimide upper housing will become brittle with
prolonged exposure to outdoor sunlight. Window glass effectively filters
longer wavelength ultraviolet light and provides excellent protection
from sunlight. Avoid contact with strong alkalis, hydrocarbons and
fuels. Clean periodically using mild soap solution and a soft cloth.
(Polycarbonate STB models are also available for use with the Run Bar;
contact Factory for assistance.)
STB Indicators - 2 Green LEDs
Power: ON – power applied
Output/fault: ON – button is activated
Output/fault: OFF – button is deactivated
Output/fault: Flashing – internal fault or blocked button on power-up
detected
Outputs
Configuration: Complementary PNP (sourcing) open-collector
transistors
Protection Circuitry: Protected against false pulse on power-up;
overload and short-circuit protection.
Response Time: 20 milliseconds ON/OFF
Output Rating
Maximum load: 150 mA
On-state saturation voltage: Less than or equal to 15 V @ full load
Off-state leakage current: Less than 1 μA
Environmental Rating
STBVP6-RB1 Run Bar Models meet IP20
STBVP6-RB2 Run Bar Models meet IP65
Operating Conditions
Temperature: 0º to +50º C (+32º to +122º F)
Maximum relative humidity: 90% @ +50º C (non-condensing)
Certifications
STB Buttons:
STBVP6-RB2...Run Bars:
38.0
[1.50"]
23.0
[0.91"]
4X 5/16-18
Threaded
Insert
4X 6.2
[0.24"]
139.2
[5.49"]
Ø31.0 [1.22"]
Knockout
26.3 [1.04"]
3X Ø23.0
[0.91"]
Knockout
76.0
[2.99"]
34.0 [1.34"]
53.0 [2.09"]
50.3 [1.98"]
137.3
[5.41"]
4X Ø8.9
[0.35"]
CL CL
CL
CL
CL
Ø22.0 [0.87"]
(1/2" NPT)
Knockout
Ø28.0 [0.87"]
(3/4" NPT) Knockout
Ø22.0 [0.87"]
(1/2" NPT)
Knockout
Ø22.0 [0.87"]
(1/2" NPT)
Knockout or
QD Connector
Ø28.0 [0.87"]
(3/4" NPT) Knockout 126.0
[4.96"]
474.0
[18.66"]
87.0
[3.43"]
Figure 12. STBVP6-RB1 Dimensions
DUO-TOUCH Run Bar with STB Buttons
10 www.bannerengineering.com - tel: 763-544-3164 Datasheet 131634_web Rev.
E