Rockwell Automation GV3000/SE Operator Interface Module (OIM) User Guide User Manual
Page 109
Index-2
GV3000/SE Operator Interface Module (OIM) User Guide, Version 2.0
L
Language, changing, 3-6
LOCAL control source, 6-4
Lock symbol, 2-7, 4-4
Log, fault, 7-3 to 7-5
M
MAGNET CURRENT PRCNT (U.006), 5-14
Main Menu - Vector regulation, B-1
Main Menu - V/Hz regulation, B-8
Manual reference, 6-1 to 6-3
changing, 6-2 to 6-3
MAXIMUM SPEED (P.004), 5-13
Menu organization, B-1 to B-13
Menus, 4-1 to 4-2
Message
alarm, 7-1 to 7-2
fault, 7-1 to 7-2
program error, 7-1
MINIMUM SPEED (P.003), 5-12
Monitor mode, 1-1, 6-1
help, 6-3
outputs, selecting, 6-2 to 6-3
Motor amperage, 6-1
MOTOR NAMEPL AMPS (U.004), 5-9
MOTOR NAMEPL AMPS (H.002), 5-9
MOTOR NAMEPLATE HP (U.022), 5-10
MOTOR NAMEPL BASE FRQ (H.001), 5-10
MOTOR NAMEPL BASE FRQ (U.003), 5-10
MOTOR NAMEPL RPM (U.005), 5-10
MOTOR NAMEPL VOLTS (U.007), 5-11
MOTOR NAMEPL VOLTS (H.000), 5-11
MOTOR POLES (U.002), 5-9
Motor speed, 6-1
Motor, starting, 1-2, 6-5
Motor, stopping, 6-5
Motor torque, 6-1
Motor voltage, 6-1
O
OIM
control source, 6-4
description, 1-1
failures, 7-8
kit contents, 3-1
menus, 4-1 to 4-2
parameters, 4-1
Operator Interface Module,
see OIM
OPTION control source, 6-4
Output
frequency, 6-2
monitor mode, 6-1
parameters, 4-6, 4-8
power, 6-1
selecting, 6-2 to 6-3
P
Parameters, 4-1
accessing, 4-3 to 4-5
configurable, 4-8
output, 4-6, 4-8
organization, B-1 to B-13
Quick Start, 5-8 to 5-14
read-only, 4-6, 4-8
restoring defaults, 4-9 to 4-10
Password program protection, 4-8 to 4-9
Power, output, 6-1
Power up, 3-4 to 3-5
Problems with drive, 7-1 to 7-2
Program
error message, 7-1
mode, 1-1
protection, password, 4-8 to 4-9
PROGRAMMING DISABLE (P.051), 4-8 to 4-9
Programming
error screen, clearing, 7-7
keys, 2-1 to 2-3
the drive, 4-1
using Quick Start, 5-1, 5-2 to 5-3
Q
Quick Start, 5-1, 5-2 to 5-4
parameter descriptions, 5-8 to 5-14
R
Read-only parameters, 4-6, 4-8
Reference, 6-2
manual, changing, 6-3
REGULATION TYPE (P.048), 5-8
Replacing OIM, 3-4
Resetting faults, 7-3, 7-4 to 7-5
RESTORE DEFAULTS (P.050), 4-9
Restoring factory defaults, 4-9 to 4-10
Reviewing alarms, 7-5 to 7-6
Reviewing faults, 7-3 to 7-4