Rockwell Automation 1770-HT8 SMART TRANSMITTER - Manual (Page 58)

Configuring the Communications
Controller
Chapter 3
3-3
Table 3.A
Push Button Operation
Pressing this button or
button combination:
Performs this task:
БББББББ
Б БББББ Б
Б БББББ Б
БББББББ
VIEW БББББББББББББББББ
Б БББББББББББББББ Б
Б БББББББББББББББ Б
БББББББББББББББББ
In run mode, takes the Communications Controller into configuration
mode.
This is the only button that has a function in run mode.
БББББББ
БББББББ
БББББББББББББББББ
БББББББББББББББББ
In configuration mode, cycles through the possible communication
parameters (displayed on the left digit).
БББББББ
Б БББББ Б
БББББББ
БББББББББББББББББ
Б БББББББББББББББ Б
БББББББББББББББББ
If you hold the button down for more than 1 second, the parameter
number will advance automatically.
БББББББ
Б БББББ Б
Б БББББ Б
Б БББББ Б
БББББББ
DATA
БББББББББББББББББ
Б БББББББББББББББ Б
Б БББББББББББББББ Б
Б БББББББББББББББ Б
БББББББББББББББББ
In configuration mode, cycles through the possible communication
settings for the parameter shown on the left. The data is displayed on
the right two digits. If you hold the button down for more than 1
second, the settings will advance and accelerate automatically.
When the left display shows 9, press DATA to enter the subĆmenu.
БББББББ
Б БББББ Б
Б БББББ Б
БББББББ
EXIT
БББББББББББББББББ
Б БББББББББББББББ Б
Б БББББББББББББББ Б
БББББББББББББББББ
In configuration mode, from the main menu, returns the Controller to
run mode without saving any changes. The change in mode takes
effect when the button is released.
From the subĆmenu, returns to the main menu.
БББББББ
Б БББББ Б
Б БББББ Б
БББББББ
VIEW + EXIT
БББББББББББББББББ
Б БББББББББББББББ Б
Б БББББББББББББББ Б
БББББББББББББББББ
In configuration mode, saves all configuration changes, and returns
the Communications Controller to run mode from either menu. The
Communications Controller will begin operating with the new
configuration as soon as it returns to run mode.
VIEW + DATA
In configuration mode, resets all communication parameters to their
factory defaults (see Table 3.B and Table 3.C ). The changes do not
take effect until the configuration is saved, and the Communications
Controller returns to run modeĊi.e. until VIEW and EXIT are pressed
simultaneously.
Before configuring the Communications Controller, you should determine
the parameters settings your network requires. If they differ from the
factory defaults shown in Table 3.B and Table 3.C, use the following
procedure to change them. While you are changing the parameters in
configuration mode, the Communications Controller continues to
communicate over its ports. The changed parameter settings do not take
effect until they are saved and the Communications Controller returns to
run mode.
Enter Configuration Mode
1. Press the VIEW button to enter configuration mode. The first
parameter number is displayed on the left display, with its current
setting in the right two displays.
Configuration Step by Step