Rockwell Automation 23C PowerFlex 400 AC Drive Packages for Fan & Pump Apps - Manual (Page 95)

Rockwell Automation Publication 23C-IN001B-EN-P - June 2013 95
3 Contactor Full Feature Bypass with Disconnect Package (Style B/N) Chapter 2
Parameter Defaults
(Style B/N)
Parameter Name Number Default
Output Freq b001 Read Only
Commanded Freq b002 Read Only
Output Current b003 Read Only
Output Voltage b004 Read Only
DC Bus Voltage b005 Read Only
Drive Status b006 Read Only
Fault 1 Code b007 Read Only
Process Display b008 Read Only
Output Power b010 Read Only
Elapsed MWh b011 Read Only
Elapsed Run Time b012 Read Only
Torque Current b013 Read Only
Drive Temp b014 Read Only
Elapsed kWh b015 Read Only
Motor NP Volts P031 Drive Rated Volts
Motor NP Hertz P032 60 Hz
Motor OL Current P033 Drive Rated Amps
Minimum Freq P034 0.0 Hz
Maximum Freq P035 60 Hz
Start Source P036 6 “2-W Lvl/Enbl” (1)
Stop Mode P037 1 “Coast, CF”
Speed Reference P038 2 “Analog In1”
Accel Time 1 P039 20.00 Secs
Decel Time 1 P040 20.00 Secs
Reset To Defalts P041 0 “Ready/Idle”
Auto Mode P042 0 “No Function” (1)
Digital In1 Sel T051 1 “Purge”
Digital In2 Sel T052 3 “Local”
Digital In3 Sel T053 10 “Clear Fault”
Digital In4 Sel T054 4 “Comm Port”
Relay Out1 Sel T055 0 “Ready/Fault”
Relay Out1 Level T056 0.0
Relay 1 On Time T058 0.0 Secs
Relay 1 Off Time T059 0.0 Secs
Relay Out2 Sel T060 2 “MotorRunning”
Relay Out2 Level T061 0.0
Relay 2 On Time T063 0.0 Secs
Relay 2 Off Time T064 0.0 Secs
Opto Out Sel T065 1 “At Frequency”
Opto Out Level T066 0.0
Opto Out Logic T068 0 “Normally Open”
Analog In 1 Sel T069 2 “0-10V”
Analog In 1 Lo T070 0.0%
Analog In 1 Hi T071 100.0%
Analog In 1 Loss T072 0 “Disabled”
Analog In 2 Sel T073 1 “4-20 mA” (1)
Analog In 2 Lo T074 0.0%
Analog In 2 Hi T075 100.0%
Analog In 2 Loss T076 0 “Disabled”
Sleep-Wake Sel T077 0 “Disabled”
Sleep Level T078 10.0%
Sleep Time T079 0.0 Secs
Wake Level T080 15.0%
Wake Time T081 0.0 Secs
Analog Out1 Sel T082 0 “OutFreq 0-10”
Analog Out1 High T083 100%
Analog Out1 Setpt T084 0.0%
Analog Out2 Sel T085 1 “OutCurr 0-10”
Analog Out2 High T086 100%
Analog Out2 Setpt T087 0.0%
Language C101 1 “English”
Comm Format C102 0 “RTU 8-N-1”
Comm Data Rate C103 3 “9600”
Comm Node Addr C104 100
Comm Loss Action C105 0 “Fault”
Comm Loss Time C106 5.0 Secs
Comm Write Mode C107 0 “Save”
Purge Frequency A141 5.0 Hz
Internal Freq A142 60.00 Hz
Preset Freq 0 A143 0.0 Hz
Preset Freq 1 A144 5.0 Hz
Preset Freq 2 A145 10.0 Hz
Preset Freq 3 A146 20.0 Hz
Accel Time 2 A147 30.00 Secs
Decel Time 2 A148 30.00 Secs
S Curve % A149 20%
PID Trim Hi A150 60.0 Hz
PID Trim Lo A151 0.0 Hz
PID Ref Sel A152 0 “PID Disabled”
PID Feedback Sel A153 0 “Analog In 1”
PID Prop Gain A154 0.01
PID Integ Time A155 2.0 Secs
PID Diff Rate A156 0.00
PID Setpoint A157 0.0%
PID Deadband A158 0.0%
PID Preload A159 0.0 Hz
Process Factor A160 30.0
Auto Rstrt Tries A163 0
Auto Rstrt Delay A164 1.0 Secs
Start At PowerUp A165 1 “Enabled” (1)
Reverse Disable A166 1 “Rev Disabled”
Flying Start En A167 1 “Enabled” (1)
PWM Frequency A168 4.0 kHz
PWM Mode A169 1 “2-Phase”
Boost Select A170 4 “45.0, VT”
Start Boost A171 2.5%
Break Voltage A172 25.0%
Break Frequency A173 15.0 Hz
Maximum Voltage A174 Drive Rated Volts
Slip Hertz @ FLA A175 2.0 Hz
DC Brake Time A176 0.0 Secs
DC Brake Level A177 Drive Rated Amps
DC Brk Time@Strt A178 0 (Disabled)
Current Limit 1 A179 Drive Rated Amps
Current Limit 2 A180 Drive Rated Amps
Motor OL Select A181 0 “No Derate”
Drive OL Mode A182 3 “Both-PWM 1st”
SW Current Trip A183 0.0 (Disabled)
Load Loss Level A184 0.0 (Disabled)
Load Loss Time A185 0 Secs
Stall Fault Time A186 0 “60 Seconds”
Bus Reg Mode A187 1 “Enabled”
Skip Frequency 1 A188 0 Hz
Skip Freq Band 1 A189 0.0 Hz
Skip Frequency 2 A190 0 Hz
Skip Freq Band 2 A191 0.0 Hz
Skip Frequency 3 A192 0 Hz
Skip Freq Band 3 A193 0.0 Hz
Compensation A194 1 “Electrical”
Reset Meters A195 0 “Ready/Idle”
Testpoint Sel A196 400
Fault Clear A197 0 “Ready/Idle”
Program Lock A198 0 “Unlocked”
Motor NP Poles A199 4
Relay Out3 Sel R221 0 “Ready/Fault”
Relay Out3 Level R222 0.0
Relay Out4 Sel R224 0 “Ready/Fault”
Relay Out4 Level R225 0.0
Relay Out5 Sel R227 0 “Ready/Fault”
Relay Out5 Level R228 0.0
Relay Out6 Sel R230 0 “Ready/Fault”
Relay Out6 Level R231 0.0
Relay Out7 Sel R233 0 “Ready/Fault”
Relay Out7 Level R234 0.0
Relay Out8 Sel R236 0 “Ready/Fault”
Parameter Name Number Default
Relay Out8 Level R237 0.0
Aux Motor Mode R239 0 “Disabled”
Aux Motor Qty R240 1 “1 Aux Mtr”
Aux 1 Start Freq R241 50.0 Hz
Aux 1 Stop Freq R242 25.0 Hz
Aux 1 Ref Add R243 0.0%
Aux 2 Start Freq R244 50.0 Hz
Aux 2 Stop Freq R245 25.0 Hz
Aux 2 Ref Add R246 0.0%
Aux 3 Start Freq R247 50.0 Hz
Aux 3 Stop Freq R248 25.0 Hz
Aux 3 Ref Add R249 0.0%
Aux Start Delay R250 5.0 Secs
Aux Stop Delay R251 3.0 Secs
Aux Prog Delay R252 0.50 Secs
Aux AutoSwap Tme R253 0.0 Hr
Aux AutoSwap Lvl R254 50.0%
Control Source d301 Read Only
Contrl In Status d302 Read Only
Comm Status d303 Read Only
PID Setpnt Displ d304 Read Only
Analog In 1 d305 Read Only
Analog In 2 d306 Read Only
Fault 1 Code d307 Read Only
Fault 2 Code d308 Read Only
Fault 3 Code d309 Read Only
Fault 1 Time-hr d310 Read Only
Fault 1 Time-min d311 Read Only
Fault 2 Time-hr d312 Read Only
Fault 2 Time-min d313 Read Only
Fault 3 Time-hr d314 Read Only
Fault 3 Time-min d315 Read Only
Elapsed Time-hr d316 Read Only
Elapsed Time-min d317 Read Only
Output Powr Fctr d318 Read Only
Testpoint Data d319 Read Only
Control SW Ver d320 Read Only
Drive Type d321 Read Only
Output Speed d322 Read Only
Output RPM d323 Read Only
Fault Frequency d324 Read Only
Fault Current d325 Read Only
Fault Bus Volts d326 Read Only
Status @ Fault d327 Read Only
(1) The default values of these parameters differ from Factory
Defaults. Setting P041 [Reset To Defalts] to 1 “Factory Rset” will
change these parameter settings to the defaults listed in the
PowerFlex 400 User Manual.
Parameter Name Number Default
ATTENTION: Parameter
A165 [Start At PowerUp] ships
from the factory enabled. This
feature allows a Run
command to automatically
cause the drive to resume
running at commanded speed
after drive input power is
restored. Equipment damage
and/or personal injury may
result if this parameter is used
in an inappropriate
application. Do not use this
function without considering
applicable local, national and
international codes, standards,
regulations or industry
guidelines.