Prescolite CFT/CFTD970HEB - Manual

Instruction
Sheet
www
.prescolite.com
• Prescolite
TollFree
Technical Support
1.888.PRS.4TEC
• Hours: 8am - 5pm ET
101 Corporate Drive • Spartanburg, SC 29303
With representatives offices in principal cities throughout North America.
Copyright 2005, 08/05 revision, All Rights Reserved - Printed in U.S.A.
Part No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .158510100
Instruction
Sheet
Plaster
Flange
CAUTION: DO NOT ATTEMPT TO MODIFY OR REWIRE FACTORY-INSTALLED WIRING ON THE FIXTURE. SAFETY AND PROPER
OPERATION OF THE FIXTURE DEPEND ON THE INTEGRITY OF THE WIRING.
1. If reflector-holding-bridge is folded,
rotate bridge to the upright position.
Secure by tightening bridge fasteners,
one on each side.
2. Bend mounting brackets as shown in
Detail”A”. Install the fixture in the ceiling
using mounting channels, bar stock,
1/2" inch EMT, or C-Channels, (by
others), placed through the adjustable
mounting brackets. Install the fixture in
the ceiling so that the weight of the
fixture is supported by the mounting
channel or bar and/or hanger wires
secured to the building structure.
Note: Housing orientation for wall
wash applications.
3. Adjust the fixture so the bottomof the
plaster flange aperture is flush with the
finished ceiling line and in aligned with
adjacent fixtures. Secure mounting
brackets by tightening wing nut on both
sides of the fixture.
4. Remove J-Box cover plate. Remove
appropriate knockout and assemble
appropriate connector for the supply
wire used. Connect ground wires to
green ground leads. Connect white
(common) to white (leads). Connect
power supply (line) to black lead(s).
Reinstall J-Box cover.
WARNING: DO NOT pinch wires
between J-Box/ballast cover and J-
Box. Consult a Qualified Electrician
for all other options that require other
wiring configurations.
6. Reflector Installation: Insert the two
outer studs on the socket mounting
bracket through the matching holes in
the top of the reflector. Secure the
reflector with two wing nuts.
7. Push reflector with the socket mounting
bracket attched into plaster flange
aperture until flange on the reflector is
flush against finished ceiling, align the
center hole in the reflector bridge and
secure with a wing nut. Note:
Orientation of reflector for wall wash
applications.
8. Install the proper lamps (by others).
Wing Nut (2)
Wing Nut
(3)(Supplied
w/HSG)
Kicker Goes Away
From Wall When
Using Wall Wash
Reflector.
This end towards
wall for wall
wash application
DETAIL “A”
Wall Wash Reflector
Mounting
Brackets are
Supplied Flat,
Bend Brackets
to align with
marks on
Flange
J-Box/Ballast
Cover
1-Lamp Reflector Shown
J-Box
Reflector Bridge,
Rotate 90° to upright
position
Adjustable
Mounting
Bracket (2)
Bridge
Fasteners (2)
Socket Mounting
Bracket
IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information
and instructions concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials,
and proper lamping. Do not install in areas subject to combustible vapors or gases. Before wiring to power supply and
during servicing or relamping, turn off power at fuse or circuit breaker. All servicing or relamping must be performed by
qualified service personnel. Product must be grounded to avoid potential electric shock or other potential hazard.
Product must be mounted in locations and at heights and in a manner consistent with its intended use, and in
compliance with the National Electrical Code and local codes. The use of accessory equipment not recommended by
the manufacturer or installed contrary to instructions may cause an unsafe condition. Do not block light emanating from
product in whole or part, as this may cause an unsafe condition. Do not allow items such as drapes, curtains, screens or
the like to come into contact with the product or to block light from the product, as this may cause an unsafe condition.
INSTALLATION INSTRUCTIONS
CFT/CFTD970HEB, 1 & 2 LAMP
HOUSINGS & REFLECTORS