AEM Infinity Supported Applications - Ford Coyote Engine with Ford Racing Control Pack - Manual (Page 26)

26
© 2014 AEM Performance Electronics
Infinity
Pin
Infinity Assignment
Pin
Destination
Ford Coyote with FR
Control Pack
Description
Infinity Hardware
Specification
Notes
C1-21
Crankshaf t Position
Sensor Hall
---
Crankshaf t Position
Sensor Hall
10K pullup to 12V. Will
work with ground or
f loating switches.
See Setup Wizard page 'Cam/
Crank' f or options.
C1-22
Camshaf t Position
Sensor 1 Hall
Engine
E-41
Camshaf t Position Bank
1 (Passenger Intake)
(CMP11)
10K pullup to 12V. Will
work with ground or
f loating switches.
See Setup Wizard page 'Cam/
Crank' f or options.
C1-23 Digital_In_2
Engine
E-42
Camshaf t Position Bank
2 (Driv erside Intake)
(CMP21)
10K pullup to 12V. Will
work with ground or
f loating switches.
See Setup Wizard page 'Cam/
Crank' f or options.
C1-24 Digital_In_3 --- Turbo Speed Hz
10K pullup to 12V. Will
work with ground or
f loating switches.
See Setup Wizard page 'Input
Function Assignment' f or
calibration constant. TurboSpeed
[RPM] = Turbo [Hz] * Turbo Speed
Calibration.
C1-25 Digital_In_4 --- Vehicle Speed Sensor
10K pullup to 12V. Will
work with ground or
f loating switches.
See Setup Wizard page 'Input
Function Assignment' f or
calibration constant.
C1-26 Digital_In_5 --- Flex Fuel
10K pullup to 12V. Will
work with ground or
f loating switches.
See channel FlexDigitalIn [Hz] f or
raw f requency input data.
C1-27 Knock Sensor 1
Engine
E-07
Knock Sensor + [KS1+]
Dedicated knock signal
processor
See Setup Wizard page 'Knock
Setup' f or options.
C1-28 Knock Sensor 2
Engine
E-45
Knock Sensor+ [KS2+]
Dedicated knock signal
processor
See Setup Wizard page 'Knock
Setup' f or options.
C1-29 +12V_Relay _Control
Ford Racing
PCM70-38
PCM Relay control
0.7A max ground sink f or
external relay control
Will activ ate at key on and at key
of f according to the conf iguration
settings.
C1-30 Power Ground
Engine
E-11
Crankshaf t Position
Sensor Shield (SHDRTN)
Power Ground Connect directly to battery ground.
C1-31 CANL_Aout
Ford Racing
PCM70-58
AEMNet CANL
Dedicated High Speed
CAN Transceiv er
Recommend twisted pair (one twist
per 2") with terminating resistor.
Contact AEM f or additional
inf ormation.
C1-32 CANH_Aout
Ford Racing
PCM70-59
AEMNet CANH
Dedicated High Speed
CAN Transceiv er
Recommend twisted pair (one twist
per 2") with terminating resistor.
Contact AEM f or additional
inf ormation.
C1-33 LowsideSwitch_1 --- Boost Control
Lowside switch, 4A max
with internal f ly back
diode. Inductiv e load
should NOT hav e f ull
time power.
See Setup Wizard Page 'LowSide
Assignment Tables' f or
conf iguration options. See 2D table
'LS1_Duty [%]' f or activ ation
settings. See Setup Wizard page
'Boost Control' f or options. Monitor
BoostControl [%] channel f or
output state.