Table 8: vp-81ksi video and audio signal codes, Table 9 – Kramer Electronics VP-81KSi User Manual
Page 35
Table of ASCII Codes for Serial Communication (Protocol 3000)
31
GTF standard............. Not supported
Additional descriptors... None
Preferred timing......... Yes
Native/preferred timing.. 1024x768p at 60Hz (4:3)
Modeline............... "1024x768" 65.000 1024 1048 1184 1344 768 771 777 806 -hsync -vsync
Detailed timing #1....... 1280x800p at 60Hz (1:1)
Modeline............... "1280x800" 71.000 1280 1328 1360 1440 800 803 809 823 +hsync -vsync
Standard timings supported
640 x 480p at 60Hz - IBM VGA
640 x 480p at 67Hz - Apple Mac II
640 x 480p at 72Hz - VESA
640 x 480p at 75Hz - VESA
800 x 600p at 56Hz - VESA
800 x 600p at 60Hz - VESA
800 x 600p at 72Hz - VESA
800 x 600p at 75Hz - VESA
1024 x 768p at 60Hz - VESA
1024 x 768p at 70Hz - VESA
1024 x 768p at 75Hz - VESA
1280 x 1024p at 75Hz - VESA
1280 x 1024p at 60Hz - VESA STD
1280 x 960p at 60Hz - VESA STD
1400 x 1050p at 60Hz - VESA STD
1440 x 900p at 60Hz - VESA STD
1600 x 1200p at 60Hz - VESA STD
1920 x 1200p at 60Hz - VESA STD
1920 x 1080p at 60Hz - VESA STD
Report information
Date generated........... 12/7/2010
Software revision........ 2.43.0.822
Operating system......... 5.1.2600.2.Service Pack 3
Raw data
00,FF,FF,FF,FF,FF,FF,00,2E,4D,08,08,02,00,00,00,0A,13,01,03,6E,24,1D,64,EE,9C,20,9C,54,4F,8F,26,21,52,56,
3F,CF,00,81,80,81,40,90,40,95,00,A9,40,D1,00,D1,C0,01,01,64,19,00,40,41,00,26,30,18,88,36,00,30,E4,10,00,00,
18,BC,1B,00,A0,50,20,17,30,30,20,36,00,20,20,00,00,00,1A,00,00,00,FC,00,56,50,2D,38,31,4B,2D,53,49,0A,20,20,
20,00,00,00,10,00,56,50,2D,38,31,4B,2D,53,49,20,0A,20,20,00,68
15 Table of ASCII Codes for Serial Communication (Protocol
3000)
lists the ASCII values to switch an input to an output for a single
VP-81KSi device. For more detailed information, see Protocol 3000
Section 17.2
Table 8: VP-81KSi Video and Audio Signal Codes
Video
Audio
IN 1
#V 1>1 CR
#A 1>1 CR
IN 2
#V 2>1 CR
#A 2>1 CR
IN 3
#V 3>1 CR
#A 3>1 CR
IN 4
#V 4>1 CR
#A 4>1 CR
IN 5
#V 5>1 CR
#A 5>1 CR
IN 6
#V 6>1 CR
#A 6>1 CR
IN 7
#V 7>1 CR
#A 7>1 CR
IN 8
#V 8>1 CR
#A 8>1 CR
lists the codes that set the audio input gain. For more detailed information,
see
U
Section 17.2