ADC HDSL4 - Manual (Page 34)

Monitoring System Activity and Performance LTPH-UM-1031-03, Issue 3
26 September 12, 2003 H4TU-C-319 List 1
Figure 12. Monitor Screen - Active Loopback with Alarms
2 To initiate a loopback, press the to cycle through the loopback choices. Press to make
your choice.
When prompted with the message: Are you sure (Y/N)? , press to initiate the loopback or to
cancel. For more information about loopbacks and troubleshooting, see “Testing” on page 42 .
3 To initiate a loopdown of all active loopbacks, press the to select LPDN, then press .
When prompted with the message: Are you sure (Y/N)? , press to initiate the loopdown or to
cancel.
Table 8. Monitor Screen Descriptions
Field Description
Active Loopback An active loopback is indicated on the lower third of the Monitor screen. Available loopbacks are
indicated by gray text. See
Table 16 on page 51 for a summary of the HDSL4 generic loopback
codes and activation methods.
Alarm Type Indicates type of alarm.
MAL Margin Alarm—Indicates the margin on HDSL4 loop has dropped below the threshold (0 to 15 dB)
set by the operator.
Armed Mode Indicates system is in an armed state for an intelligent repeater loopback command.
BERT Status Provides BERT Generator status, elapsed time, and BERT results.
DS1 Errors
ES Count Errored Seconds—The sum of the Errored Seconds-Line (ES-L) and Errored Seconds-Path (ES-P)
counts detected on the DS1 input over a 24-hour period. Errors included are: DS1 frame errors,
BPV, and ESF CRC errors.
SES Count Severely Errored Seconds—The sum of the DS1 Severely Errored Seconds-Line (SES-L) and
Severely Errored Seconds-Path (SES-P) counts over the last 24 hours.
Continued
Armed Mode Loop Attenuation Alarm Type HDSL4 Errors
Frame Code and Type Active Loopback Margin System Status
DS1 Errors BERT Status
Monitor Performance Event Log Config Inventory Report Rlogon Help
BERT Status: ACTIVE Time Elapsed: 00:00:50 Error Rate: <1.00E-10
M =16 15 16 17 16 16
LA =17 17 16 16 17 17
ARM INSL=23 23 22 22 23 23
ES =0 0 0 0 28 0
ESF SES =0 0 0 0 23 0 ESF
B8ZS UAS =0 0 0 0 171 151 B8ZS
------->+-----+ LP1 +-----+ LP1 +-----+ LP1 +-----+-------
>
| TUC |=
MAL ========| DU1 |============| DU2 |============| TUR |
ESF | | | | | | | | ESF
B8ZS | LPF |============| |============| |============| | B8ZS
<-------+-----+ LP2 +-----+ LP2 +-----+ LP2 +-----+<------
-
ES =6884 M =15 15 14 15 16 16 ES =0
SES=0 LA =18 17 17 16 17 17 SES=0
UAS=56 INSL=24 23 23 22 23 23 UAS=0
ES =0 0 0 0 2 2 PRM=0
SES =0 0 0 0 1 0
UAS =0 0 0 0 0 0
----------------------------------- LOOPBACKS -------------------------------
Active Loopbacks : NLOC-PL
Press to select LB New Loopback: NLOC – Loopdown All Active Loopbacks
and to activate (LPDN,NLOC,CREM,NREM,CLOC)
ID: xxxx--xxxx—-xxxx--xxxx 02/01/2002 12:30:01 H4TU-C System: OK ___
Insertion Loss
SPACEBAR ENTER
Y N
SPACEBAR ENTER
Y N