Red Lion PXU - Manual (Page 31)

31
REGISTER
ADDRESS
REGISTER NAME LOW LIMIT HIGH LIMIT
FACTORY
SETTING
ACCESS COMMENTS
LOCKOUT PARAMETERS
40101 Setpoint Access 0 4 0 Read/Write 0 = dISP, 1 = ParA, 2 = HIdE, 3 = LOC, 4 = dSPr
40102 Output 1 Power Access 0 4 1 Read/Write 0 = dISP, 1 = ParA, 2 = HIdE, 3 = LOC, 4 = dSPr
40103 Output 2 Power Access 0 4 1 Read/Write 0 = dISP, 1 = ParA, 2 = HIdE, 3 = LOC, 4 = dSPr
40104 Setpoint Ramp Rate Access 0 4 1 Read/Write 0 = dISP, 1 = ParA, 2 = HIdE, 3 = LOC, 4 = dSPr
40105 PID Group Access 0 4 1 Read/Write 0 = dISP, 1 = ParA, 2 = HIdE, 3 = LOC, 4 = dSPr
40106 Controller Status (Run/Stop) Access 0 4 0 Read/Write 0 = dISP, 1 = ParA, 2 = HIdE, 3 = LOC, 4 = dSPr
40107 Output Power Offset Access 1 3 1 Read/Write 1 = ParA, 2 = HIdE, 3 = LOC
40108 Proportional band Access 1 3 1 Read/Write 1 = ParA, 2 = HIdE, 3 = LOC
40109 Integral time Access 1 3 1 Read/Write 1 = ParA, 2 = HIdE, 3 = LOC
40110 Derivative time Access 1 3 1 Read/Write 1 = ParA, 2 = HIdE, 3 = LOC
40111 Integration Default Access 1 3 3 Read/Write 1 = ParA, 2 = HIdE, 3 = LOC
40112 Alarm 1 Value Access 1 3 1 Read/Write 1 = ParA, 2 = HIdE, 3 = LOC
40113 Alarm 2 Value Access 1 3 1 Read/Write 1 = ParA, 2 = HIdE, 3 = LOC
40114 Alarm 3 Value Access 1 3 1 Read/Write 1 = ParA, 2 = HIdE, 3 = LOC
40115 Alarm Reset Access 1 3 1 Read/Write 1 = ParA, 2 = HIdE, 3 = LOC
40116 Setpoint Select Access 1 3 1 Read/Write 1 = ParA, 2 = HIdE, 3 = LOC
40117 Auto-Tune Start Access 2 3 2 Read/Write 2 = HIdE, 3 = LOC
40118 Auto Control Mode Access 2 3 2 Read/Write 2 = HIdE, 3 = LOC
40119 Control Mode Transfer Access 2 3 2 Read/Write 2 = HIdE, 3 = LOC
40120 Deviation Value Access 0 3 0 Read/Write 0 = dISP, 3 = LOC
40121 Access Code -125 125 0 Read/Write
0 = Full access to display, parameter, hidden, and
configuration loops; -1 to -125 = Code necessary to
access configuration loop only; 1 to 125 = Code
necessary to access hidden and configuration loops
ALARM PARAMETERS
40131 Alarm 1 Action 0 18 0 Read/Write
0 = No, 1 = AbHI, 2 = AbLO, 3 = AUHI, 4 = AULO,
5 = d-HI, 6 = d-Lo, 7 = b-In, 8 = b-ot, 9 = InPt,
10 = Ct1, 11 = Ct2, 12 = SOAK, 13 = r-UP,
14 = r-dn, 15 = rUn, 16 = HoLd, 17 = StoP, 18 = End
40132 Alarm 1 Annunciator 0 1 0 Read/Write 0 = Normal, 1 = Reverse
40133 Alarm 1 Reset Mode 0 1 0 Read/Write 0 = Automatic, 1 = Latched
40134 Alarm 1 Standby 0 1 0 Read/Write 0 = No, 1 = Yes
40135 Alarm 1 Value -999 9999 100 Read/Write 1 = 1 Display unit
40136 Input Fail Alarm 1 Action 0 1 0 Read/Write 0 = Off; 1 = On
40137 Alarm 2 Action 0 18 0 Read/Write
0 = No, 1 = AbHI, 2 = AbLO, 3 = AUHI, 4 = AULO,
5 = d-HI, 6 = d-Lo, 7 = b-In, 8 = b-ot, 9 = InPt,
10 = Ct1, 11 = Ct2, 12 = SOAK, 13 = r-UP,
14 = r-dn, 15 = rUn, 16 = HoLd, 17 = StoP, 18 = End
40138 Alarm 2 Annunciator 0 1 0 Read/Write 0 = Normal, 1 = Reverse
40139 Alarm 2 Reset Mode 0 1 0 Read/Write 0 = Automatic, 1 = Latched
40140 Alarm 2 Standby 0 1 0 Read/Write 0 = No, 1 = Yes
40141 Alarm 2 Value -999 9999 200 Read/Write 1 = 1 Display unit
40142 Input Fail Alarm 2 Action 0 1 0 Read/Write 0 = Off; 1 = On
40143 Alarm 3 Action 0 18 0 Read/Write
0 = No, 1 = AbHI, 2 = AbLO, 3 = AUHI, 4 = AULO,
5 = d-HI, 6 = d-Lo, 7 = b-In, 8 = b-ot, 9 = InPt,
10 = Ct1, 11 = Ct2, 12 = SOAK, 13 = r-UP,
14 = r-dn, 15 = rUn, 16 = HoLd, 17 = StoP, 18 = End
40144 Alarm 3 Annunciator 0 1 0 Read/Write 0 = Normal, 1 = Reverse
40145 Alarm 3 Reset Mode 0 1 0 Read/Write 0 = Automatic, 1 = Latched
40146 Alarm 3 Standby 0 1 0 Read/Write 0 = No, 1 = Yes
40147 Alarm 3 Value -999 9999 300 Read/Write 1 = 1 Display unit
40148 Input Fail Alarm 3 Action 0 1 0 Read/Write 0 = Off; 1 = On
40149 Alarm Hysteresis 0
250(.0)° or
2500 (process)
0 Read/Write 1 = 1 Display unit; The same value applies to all
alarms.
40150 Change Color Intensity 0 4 0 Read/Write 0 = OFF, 1 = Any Alarm, 2 = AL-1, 3 = AL-2,
4 = AL-3