Red Lion PXU - Manual (Page 16)

16 16
ACCESS CODE

to

7.3 mOdule 3 - l
OCKOuT
p
arameTers
(
3-LC
)
SP OP2 OP1 SPrP PId r-S
SETPOINT OUTPUT 1
POWER
OUTPUT 2
POWER
CONTROLLER
STATUS
3-LC
PID
GROUP RAMP RATE
SETPOINT
OPOF ProP Intt dErt
CNFP
OUTPUT
POWER
OFFSET
PROPORTIONAL
BAND
INTEGRAL
TIME
DERIVATIVE
TIME
dInt
INTEGRATION
DEFAULT
AL-2 AL-1 AL-3 ALrS SPSL
ALARM 1
VALUE
ALARM 2
VALUE
SETPOINT
SELECT
ALARM
RESET VALUE
ALARM 3
tUNE CtrL dEv CodE
AUTO-TUNE
START
CONTROL
MODE
DEVIATION
VALUE
trnF
CONTROL
MODE
TRANSFER
ACCESS
CODE
P P
Programming/model dependent.
PARAMETER MENU
SELECTION DESCRIPTION
dISP Display: accessible in Display Loop.
PArA Parameter: accessible in Parameter Loop
HIdE Hide: accessible in Hidden Loop.
LOC Locked: not accessible in loops.
dSPr
Display/read: read only in Display Loop, but read/write
in Hidden Loop.
The following parameters can be configured for the selections described
above. See Programming Loops section for a description of loops and
parameters.
PARAMETER SELECTION
FACTORY
SETTING
SP dISP
,
PArR
,
HIdE
,
LOC
,
dSPr dISP
OP1 dISP
,
PArR
,
HIdE
,
LOC
,
dSPr PArR
OP2 dISP
,
PArR
,
HIdE
,
LOC
,
dSPr PArR
SPrP dISP
,
PArR
,
HIdE
,
LOC
,
dSPr PArR
PId dISP
,
PArR
,
HIdE
,
LOC
,
dSPr PArR
r-S dISP
,
PArR
,
HIdE
,
LOC
,
dSPr dISP
OPOF PArR
,
HIdE
,
LOC PArR
ProP PArR
,
HIdE
,
LOC PArR
Intt PArR
,
HIdE
,
LOC PArR
dErt PArR
,
HIdE
,
LOC PArR
dInt PArR
,
HIdE
,
LOC LOC
AL-1 PArR
,
HIdE
,
LOC PArR
AL-2 PArR
,
HIdE
,
LOC PArR
AL-3 PArR
,
HIdE
,
LOC PArR
ALrS PArR
,
HIdE
,
LOC PArR
SPSL PArR
,
HIdE
,
LOC PArR
tUNE HIdE
,
LOC HIdE
CtrL HIdE
,
LOC HIdE
trnf HIdE
,
LOC HIdE
dEv dISP
,
LOC dISP
Parameters may not appear in selected loop if not applicable to current
operating mode.
Ex. 1. If
At2
=
NONE
,
AL-2
will not be displayed in selected loop.
2. If
CtrL
=
ONOF
, PID parameters will not be displayed in selected loop.
0
Full access to Display, Hidden, and
Configuration Loops
-1
to
-125
Code necessary to access
Configuration Loop only.
*
1
to
125
Code necessary to access Hidden
and Configuration Loops.
*
* If PLOC is active, Configuration Loop is not accessible.



C
Shaded parameters are programming/model dependent.