B.65 condition:questionable:condition? query, B.66 status:questionable:enable command, B.67 status:questionable:enable? query – KEPCO EL Series Electronic Load Operator Manual P/N 243-1295 Firmware Version 3.63 through 3.86 User Manual
Page 73: B.68 system:communicate[:gpib]:address command, B.69 system:communicate[:gpib]:address? query, B.70 system:communicate:echo command, B.65, Condition, B.66, Statu

SERIES EL 070312
B-11
B.65 CONDition:QUEStionable:CONDition? QUERY
STAT:QUES:COND?
Syntax:
Short Form: STAT:QUES:COND?
Long Form: STATus:QUEStionable:CONDition?
Return Value:
Description: Returns the value of the Questionable Condition Register. The Questionable Condition Register
contains unlatched real-time information about questionable conditions of the electronic load. Bit set to
1 = condition (active, true); bit reset to 0 = condition (inactive, false). (See example, PAR. B.61.)
B.66 STATus:QUEStionable:ENABle COMMAND
STAT:QUES:ENAB
Syntax:
Short Form: STAT:QUES:ENAB
Description: Programs Questionable Condition Enable Register. The Questionable Condition Enable Register
determines which conditions are allowed to set the Questionable Condition Register; it is a mask for
enabling
specific bits in the Questionable Event register that can cause the questionable summary bit
(bit 3) of the Status Byte register to be set. The questionable summary bit is the logical OR of all the
enabled bits in the Questionable Event register
.
Bit set to 1 = function enabled (active, true); bit reset
to 0 = function disabled (inactive, false)
.
B.67 STATus:QUEStionable:ENABle? QUERY
STAT:QUES:ENAB?
Syntax:
Short Form: STAT:QUES:ENAB?
Long Form: STATus:QUESionable:ENABle?
Return Value:
Description: Reads Questionable Condition Enable Register. Electronic load returns value of Questionable
Condition Enable Register, indicating which conditions are being monitored. Bit set to 1 = function
enabled (active, true); bit reset to 0 = function disabled (inactive, false)
.
B.68 SYSTem:COMMunicate[:GPIB]:ADDRess COMMAND
SYST:COMM[:GPIB]:ADDR
Syntax:
Short Form: SYST:COMM[:GPIB]:ADDR
Long Form: SYSTem:COMMunicate[:GPIB]:ADDRess
Where:
is 10.
Description: Sets the GPIB Address to be used during communication over the GPIB interface. After setting
the address, the EL Load must be power cycled (turned off, then on) in order for the new GPIB
address to take effect. Command is not valid from the GPIB interface.
B.69 SYSTem:COMMunicate[:GPIB]:ADDRess? QUERY
SYST:COMM[:GPIB]:ADDR?
Syntax:
Short Form: SYST:COMM[:GPIB]:ADDR?
Long Form: SYSTem:COMMunicate[:GPIB]:ADDRess?
Returns:
Description: Returns the GPIB Address used during communication over the GPIB interface. Command is
not valid from the GPIB interface.
B.70 SYSTem:COMMunicate:ECHO COMMAND
SYST:COMM:ECHO
Syntax:
Short Form: SYST:COMM:ECHO
Where: 1 or ON turns on echo, 0 or off turns off echo
Description: Causes the EL Load to return the parsed string to the user. The parsed string may not be the com-
plete string sent to the EL; the parsed string contains the short form mnemonic for the command. Fac-
tory default is SYST:COMM:ECHO off.