B.34 [source:]power:protection command, B.35 [source:]power:protection? query, B.32 – KEPCO EL Series Electronic Load Operator Manual P/N 243-1295 Firmware Version 3.63 through 3.86 User Manual

Page 68: Source, B.33, B.34, B.35, B.36, B.37, B.38

B-6

SERIES EL 070312

B.32 [SOURce:]POWer[:LEVel][:IMMediate][:AMPlitude] COMMAND

POW

Syntax:

Short Form: [SOUR:]POW[:LEV][:IMM][:AMP]
Long Form: [SOURce:]POWer[:LEVel][:IMMediate][:AMPlitude]
Where = power setpoint

Description: Establishes power setpoint. The power setpoint only affects the load when the load is in Power

mode of operation.

B.33 [SOURce:]POWer[:LEVel][:IMMediate][:AMPlitude]? QUERY

POW?

Syntax:

Short Form: [SOUR:]POW[:LEV][:IMM][:AMP]?
Long Form: [SOURce:]POWer[:LEVel][:IMMediate][:AMPlitude]?
Returns = power setpoint

Description: Indicates power setpoint.

B.34 [SOURce:]POWer:PROTection COMMAND

POW:PROT

Syntax:

Short Form: [SOUR:]POW:PROT

Long Form: [SOURce:]POWer:PROTection

where = power protection setpoint

Description: Selects power protection setpoint. This is a user-defined value which, if exceeded during operation,

causes a FAULT condition, forcing the load to disengage.

B.35 [SOURce:]POWer:PROTection? QUERY

POW:PROT?

Syntax:

Short Form: [SOUR:]POW:PROT?

Long Form: [SOURce:]POWer:PROTection?

Returns = power protection setpoint

Description: Indicates power protection setpoint.

B.36 [SOURce:]POWer:PROTection:STATe[:LEVel] COMMAND

POW:PROT:STAT 0

Syntax:

Short Form: [SOUR:]POW:PROT:STAT[:LEV] 0
Long Form: [SOURce:]POWer:PROTection:STATe[:LEVel] 0

Description: Clears power protection error.

B.37 [SOURce:]POWer:PROTection:STATe[:LEVel]? QUERY

POW:PROT:STAT?

Syntax:

Short Form: [SOUR:]POW:PROT:STAT[:LEV]?
Long Form: [SOURce:]POWer:PROTection:STATe[:LEVel]?
where: = 1 (power protection error occurred)

0 (power protection error has not occurred)

Description: Indicates whether a power protection error has occurred (1) or not (0).

B.38 [SOURce:]RESistance[:LEVel][:IMMediate][:AMPlitude] COMMAND

RES

Syntax:

Short Form: [SOUR:]RES[:LEV][:IMM][:AMP]
Long Form: [SOURce:]RESistance[:LEVel][:IMMediate][:AMPlitude]
Where: = resistance setpoint

Description: Establishes resistance setpoint. The resistance setpoint only affects the load when the load is in

Resistance mode of operation. Resistance setpoint is stored in non-volatile memory; value is restored
upon power-up.

B.39 [SOURce:]RESistance[:LEVel][:IMMediate][:AMPlitude]? QUERY

RES?

Syntax:

Short Form: [SOUR:]RES[:LEV][:IMM][:AMP]?
Long Form: [SOURce:]RESistance[:LEVel][:IMMediate][:AMPlitude]?
Returns: = resistance setpoint

Description: Indicates resistance setpoint.