beautypg.com

Limitations, Hqos for vpls traffic overview – Brocade MLX Series and NetIron Family (Supporting Multi-Service IronWare R05.6.xx) User Manual

Page 22

background image

14

Brocade MLX Series and NetIron Family Documentation Updates

53-1003301-07

HQoS for VPLS traffic overview

1

Brocade (config-hqos-scheduler-policy policy-2)# shaper-rate 1000000

Brocade (config-hqos-scheduler-policy policy-2)# shaper-burst-size 64

Brocade (config-hqos-scheduler-policy policy-2)# scheduler-type strict

Brocade (config-hqos-scheduler-policy policy-2)# scheduler-flow flow-2-0

scheduler- input 0 scheduler-policy policy-3

Brocade (config-hqos-scheduler-policy policy-2)# scheduler-flow flow-2-1

scheduler- input 1 scheduler-policy policy-3

Brocade (config-hqos-scheduler-policy policy-2)#

Brocade (config-hqos-scheduler-policy policy-2)#HQOS scheduler-policy policy-3

leve l level-2

Brocade (config-hqos-scheduler-policy policy-3)# shaper-rate 20000

Brocade (config-hqos-scheduler-policy policy-3)# shaper-burst-size 64

Brocade (config-hqos-scheduler-policy policy-3)# scheduler-type strict

Brocade (config-hqos-scheduler-policy policy-3)# scheduler-flow flow-3-0

scheduler- input 0 scheduler-policy policy-4

Brocade (config-hqos-scheduler-policy policy-3)# scheduler-flow flow-3-1

scheduler- input 1 scheduler-policy policy-4

Brocade (config-hqos-scheduler-policy policy-3)#!

Brocade (config-hqos-scheduler-policy policy-3)#HQOS scheduler-policy policy-4

leve l level-3

Brocade (config-hqos-scheduler-policy policy-4)# shaper-rate 2000

Brocade (config-hqos-scheduler-policy policy-4)# shaper-burst-size 10

Brocade (config-hqos-scheduler-policy policy-4)# scheduler-type strict

Brocade (config)#router mpls

Brocade (config-mpls)#mpls-interface e3/3

Brocade (config-mpls-if-e100-3/3)#mpls-interface ve 200

Brocade (config-mpls-if-ve-200)#

Brocade (config-mpls-if-ve-200)# vpls test1 5000

Brocade (config-mpls-vpls-test1)# vpls-peer 1.1.1.2

Brocade (config-mpls-vpls-test1)# vlan 100

Brocade (config-mpls-vpls-test1-vlan-100)# tagged ethe 4/1

2. Use the following commands to configure HQoS for VPLS on Node PE11

Brocade (config)# interface ethernet 3/3

Brocade (config-if-eth-3/3) # hqos service-policy output policy-1

Brocade (config-if-eth-3/3) # hqos-map flow-1-1.flow-2-1.flow-3-1 match vpls 5000

peer 1.1.1.2

Brocade (config-if-eth-3/3)# enable

Limitations

The same configuration must be applied on both MCT nodes.

Any module (except BR-MLX-10Gx24 and BR-MLX-40Gx4-X) can be used for ingress traffic
destined for an HQoS port. Only BR-MLX-10Gx8-M and BR-MLX-10Gx8-X modules support
egressing HQoS traffic.

It is recommended that you configure the HQoS Map on all the MPLS Uplink interfaces.

BGP Auto-discovery for VPLS is not supported.

HQoS will not work properly in MCT VPLS failure scenario e.g. CCP-DOWN or Spoke Down.