Brocade Flow Vision Administrators Guide (Supporting Fabric OS v7.3.0) User Manual
Page 44
\ --------------------------------------
\ |- |219 |no |- |- |
\ --------------------------------------
+ Denotes feature is currently activated for the flow
DCX_Backbone128:admin> flow --show b2e_dst_dcx -feature monitor
===========================================================================
Name : b2e_dst_dcx Features: mon(Active) noConfig: Off
Definition: EgrPort(219),SrcDev(20:02:00:11:0d:51:00:00),
DstDev(10:00:00:05:1e:e8:e2:00)
Flow Monitor (Activated):
Monitor time: | Mon Jul 17 15:59:58 UTC 2013 |
---------------------------------------------------------
------------------------------------------------------------------------------------------------
| Tx Frames Count| Tx Frames per Sec.| Tx Bytes Count| Tx Throughput(Bps)| Avg Tx Frm Sz(Bytes)|
------------------------------------------------------------------------------------------------
| 142.93M | 3.74M | 26.97G | 724.78M | 204 |
------------------------------------------------------------------------------------------------
Monitoring an edge-to-backbone flow identified by WWNs
In a network set up as shown in
on page 41, for a flow passing from Device A to Device C
that is ingressing through EX_Port1, the source device (srcdev) is port “WWN a”, the destination
device (dstdev) is port “WWN c”, and the ingress port (ingrport) is EX_Port1. (Traffic is running from
right to left, and the flow definitions are based on the Edge 1 Fabric’s perspective.)
The following example creates a flow that filters out frames passing from an edge fabric to the
backbone fabric using a specific ingress port. The first command shows the available ports and the
available Fibre Channel routers. The second command creates a Flow Monitor flow named
“e2b_src_dcx” between device 10:00:00:05:1e:e8:e2:00 and device 20:02:00:11:0d:51:00:00
egressing through port 219, and the last command displays the results of the flow.
NOTE
The slash character (\) in the example indicates a break inserted because the output is too long to
display here as a single line.
DCX_Backbone128:admin> switchshow |grep Port
Index Slot Port Address Media Speed State Proto \
37 3 5 012500 id N16 Online FC EX-Port 10:00:00:05:33:ef:f1:1c \
47 3 15 012f00 id N8 Online FC F-Port 20:02:00:11:0d:51:00:00 \
219 10 27 01db00 id N16 Online FC EX-Port 10:00:00:05:33:ee:d0:a5 \
E-Port 50:00:51:e4:91:9e:0f:28 \
\
\ "Wasp_e2" (fabric id=50)(Trunk master)
\
\ "Gnat_e1" (fabric id=100)(Trunk master)
\ "fcr_xd_2_100"
DCX_Backbone128:admin> flow --create e2b_src_dcx -feature monitor -ingrport 219
-srcdev 10:00:00:05:1e:e8:e2:00 -dstdev 20:02:00:11:0d:51:00:00
DCX_Backbone128:admin>flow --show
---------------------------------------------------------------------------- \
Flow Name | Feature | SrcDev | DstDev | \
---------------------------------------------------------------------------- \
e2b_src_dcx |mon+ |10:00:00:05:1e:e8:e2:00 |20:02:00:11:0d:51:00:00 | \
---------------------------------------------------------------------------- \
\ --------------------------------------
\ |IngrPt|EgrPt|BiDir| LUN |FrameType |
\ --------------------------------------
\ |219 |- |no |- |- |
\ --------------------------------------
+ Denotes feature is currently activated for the flow
DCX_Backbone128:admin> flow --show e2b_src_dcx -feature monitor
===========================================================================
Name: e2b_src_dcx Features: mon(Active) noConfig: Off
Definition: IngrPort(219),SrcDev(10:00:00:05:1e:e8:e2:00),
DstDev(20:02:00:11:0d:51:00:00)
Monitoring an edge-to-backbone flow identified by WWNs
44
Flow Vision Administrators Guide
53-1003168-01