Brocade Flow Vision Administrators Guide (Supporting Fabric OS v7.3.0) User Manual
Page 42
219 10 27 01db00 id N16 Online FC EX-Port 10:00:00:05:33:ee:d0:a5 \
E-Port 50:00:51:e4:91:9e:0f:28 \
\ "Wasp_e2" (fabric id=50)(Trunk master)
\
\ "Gnat_e1" (fabric id=100)(Trunk master)
\ "fcr_xd_2_100"
DCX_Backbone128:admin> flow --create e2e_src_dcx_wwn -feature monitor -ingrport 219
-srcdev 10:00:00:05:1e:e8:e2:00 -dstdev 20:00:00:11:0d:e4:18:00
DCX_Backbone128:admin>flow --show
---------------------------------------------------------------------------------------- \
Flow Name | Feature | SrcDev | DstDev | \
---------------------------------------------------------------------------------------- \
e2e_src_dcx_wwn |mon+ |10:00:00:05:1e:e8:e2:00 |20:00:00:11:0d:e4:18:00 | \
---------------------------------------------------------------------------------------- \
\ -------------------------------------
\ IngrPt|EgrPt |BiDir| LUN |FrameType|
\ -------------------------------------
\ 219 |- |no |- |- |
\ -------------------------------------
\ + Denotes feature is currently activated for the flow
DCX_Backbone128:admin> flow --show e2e_src_dcx_wwn -feature monitor
==================================================================
Name : e2e_src_dcx_wwn Features: mon(Active) noConfig: Off
Definition: IngrPort(219),SrcDev(10:00:00:05:1e:e8:e2:00),
DstDev(20:00:00:11:0d:e4:18:00)
Flow Monitor (Activated):
Monitor time: | Mon Jun 17 14:59:58 UTC 2013 |
-----------------------------------------------------------------
-----------------------------------------------------------------------------------------------------
| Rx Frames Count | Rx Frames per Sec. | Rx Bytes Count | Rx Throughput(Bps) | Avg Rx Frm Sz(Bytes)|
-----------------------------------------------------------------------------------------------------
| 2.85G | 8.44M | 387.88G | 1.12G | 132 |
-----------------------------------------------------------------------------------------------------
Monitoring an edge-to-edge flow through an egress port identified by a WWN
In a network set up as shown in
on page 41, for a flow passing from Device B to Device A
that is egressing through EX_Port1, the source device (srcdev) is port “WWN b”, the destination
device (dstdev) is port “WWN a”, and the egress port (egrport) is EX_Port1. (Traffic is running from
right to left, and the flow definitions are based on the Edge 1 Fabric’s perspective.)
The following example creates a flow that filters out frames passing from one edge fabric to another
edge fabric using a specific egress port on the backbone. The first command shows the available ports
and the available Fibre Channel routers. The second command creates a Flow Monitor flow named
“e2e_dst_dcx” between device 20:00:00:11:0d:e4:18:00 and device 10:00:00:05:1e:e8:e2:00
egressing through port 219, and the last command displays the results of the flow.
NOTE
The slash character (\) in the example indicates a break inserted because the output is too long to
display here as a single line.
DCX_Backbone128:admin> switchshow |grep Port
Index Slot Port Address Media Speed State Proto
37 3 5 012500 id N16 Online FC EX-Port 10:00:00:05:33:ef:f1:1c \
47 3 15 012f00 id N8 Online FC F-Port 20:02:00:11:0d:51:00:00 \
219 10 27 01db00 id N16 Online FC EX-Port 10:00:00:05:33:ee:d0:a5 \
E-Port 50:00:51:e4:91:9e:0f:28 \
\ "Wasp_e2" (fabric id=50)(Trunk master)
\
\ "Gnat_e1" (fabric id=100)(Trunk master)
\ "fcr_xd_2_100"
DCX_Backbone128:admin> flow --create e2e_dst_dcx -feature monitor -egrport 219
Monitoring an edge-to-edge flow through an egress port identified by a WWN
42
Flow Vision Administrators Guide
53-1003168-01