Watlow Series 922 - Manual (Page 58)

58
WATLOW Series 922 User's Manual How To Program the Series 922, Chapter 6
PROGRAM
Prompt Description Range Default Your Settings
FILE? Current system file to edit. 1 - 10 1
STEP Select step number to view or edit. Press MODE for step-type
prompt. To change step-type use the increment/decrement
key and press ENTER.
1-99 1
SETPOINT - Step-Type
SP1 Enter the temperature to achieve for the step's ending set point
for Channel 1 according to the HOUR, MIN, SEC parameters.
R1L and R1H -
SP2 Enter the temperature to achieve for the step's ending set point
for Channel 2 according to the HOUR, MIN, SEC parameters.
R2L and R2H -
Dependent on TYP parameter under SPCLFUNC.
HOUR Enter the hours programmed for this step. 0 - 23 hours -
MIN Enter the minutes programmed for this step. 0 - 59 minute -
SEC Enter the seconds programmed for this step. 0 - 59 seconds -
EV1 Enter the Event Output 1 status. Dependent on output & AUX1. OFF or ON -
EV2 Enter the Event Output 2 status. Dependent on output & AUX2. OFF or ON -
EV3 Enter the Event Output 3 status. Dependent on output board. OFF or ON -
EV4 Enter the Event Output 4 status. Dependent on output board. OFF or ON -
EV5 Enter the Event Output 5 status. Dependent on output board. OFF or ON -
EV6 Enter the Event Output 6 status. Dependent on output board. OFF or ON -
EV7 Enter the Event Output 7 status. Dependent on output board. OFF or ON -
EV8 Enter the Event Output 8 status. Dependent on output board. OFF or ON -
RETURN Press the ENTER key to return to the SYSTEM prompt.
Press the MODE key to return to the FILE? prompt.
JUMPLOOP - Step-Type
JS Enter the step number the 922 will jump to. 1 - 99 1
JC Enter the number of times the 922 will jump to the step
indicated by JS.
0 - 100 0
RETURN Press the ENTER key to return to the SYSTEM prompt.
Press the MODE key to return to the FILE? prompt.
WAITFOR - Step-Type
WHR Enter the hours the 922 will wait relative to the beginning
of the step.
0 - 23 hours -
WMN Enter the minutes the 922 will wait relative to the beginning
of the step.
0 - 59 minutes -
WE Enter the state of the event input to wait for before
continuing the program.
OPEN or CLSE -
W1 Enter a value to compare with the process variable of R1L - R1H -
Channel 1.
W2 Enter a value to compare with the process variable of R2L - R2H -
Channel 2. Dependent on TYP parameter under SPCLFUNC.
RETURN Press the ENTER key to return to the SYSTEM prompt.
Press the MODE key to return to the FILE? prompt.
AUTOSTART - Step-Type
DAY Enter the number of days for the 922 to wait until
AUTOSTART takes place.
0 - 6 days -
HOUR Enter the number of hours for the 922 to wait for the time-of-
day clock before AUTOSTART takes place.
0 - 23 hours -
MIN Enter the number of minutes for the 922 to wait for the time-of
day clock before AUTOSTART takes place.
0 - 59 minutes -
RETURN Press the ENTER key to return to the SYSTEM prompt.
Press the MODE key to return to the FILE? prompt.
STOP - Step-Type
STOP
Press ENTER to display the last step of the program.
RETURN Press the ENTER key to return to the SYSTEM prompt.
Press the MODE key to return to the FILE? prompt.
LINK - Step-Type
FILE? The current system file will always link to
Step 1 in the file specified.
1 - 10 1
RETURN Press the ENTER key to return to the SYSTEM prompt.
Press the MODE key to return to the FILE? prompt.
PROGRAM Menu
Make photocopies, keep original clean.
Table 10 -
PROGRAM Prompts
and Description.