KB Electronics IODA, Input/Output Module for use with all KBDA/KBMK Controls - Manual (Page 41)

41
FUNCTION GROUP 7
MULTI-FUNCTION INPUT TERMINALS
Function
No. Description Range/Code
Factory
Setting
Actual
Setting
7.00 *
Multi-Function Input
Terminal 1
1
0000
7.01 *
Multi-Function Input
Terminal 2
1
0001
7.02 *
Multi-Function Input
Terminal 3
1
0002
7.03 *
Multi-Function Input
Terminal 4
1 0009
7.04 *
Multi-Function Input
Terminal 5
1 0010
7.05 *
Multi-Function Input
Terminal 6
1
0003
7.06 *
Multi-Function Input
Terminal 7
1
0000: Preset Frequency Operation 2
0001: Preset Frequency Operation 2
0002: Preset Frequency Operation 2
0003: Up Frequency Command 3
(See 7.14)
0004: Down Frequency Command 3
(See 7.14)
0005: Accel/Decel 2 (See 7.16)
0006: Forward/Stop Command
4
0007: Reverse/Stop Command 4
0008: External Fault (N.O. Contact)
0009: Reset
0010: N.O. Start
4
(2-Wire or 3-Wire Start/Stop)
0011: N.C. Stop
4
(3-Wire Start/Stop)
0012: External Fault (N.C. Contact)
0004
7.07 Preset Frequency 1 (Hz) 0.00 – 240.0 5.00
7.08 Preset Frequency 2 (Hz) 0.00 – 240.0 10.00
7.09 Preset Frequency 3 (Hz) 0.00 – 240.0 20.00
7.10 Preset Frequency 4 (Hz) 0.00 – 240.0 25.00
7.11 Preset Frequency 5 (Hz) 0.00 – 240.0 30.00
7.12 Preset Frequency 6 (Hz) 0.00 – 240.0 35.00
7.13 Preset Frequency 7 (Hz) 0.00 – 240.0 40.00
7.14
Up/Down Frequency
Control Mode
0000: Free-Running 5
0001: Incremental Change
(See
7.15)
0000
7.15
Increment of Up/Down
Frequency (Hz)
0.01 – 30.00 1.00
7.16
Accel/Decel 2 Time
(Seconds)
0.3 – 180.0 1.5
Note: 1. Each of the 7 Multi-Function Inputs can be programmed for any of the respective
function codes ("0000" – "0011"). 2. Preset Frequencies 1 – 7 are obtained by selecting a
specific combination of 3 Multi-Function Input Terminals. The specific frequencies are
programmed in Function Nos. 7.07 – 7.13. 3. For Up/Down Frequency Commands (codes
"0003" and "0004"), Frequency Control (Function No. 2.00) must be set to Up/Down Using
MFITs (code "0005"). 4. For Forward/Reverse Stop Commands (codes "0006" and "0007")
and N.O. Start / N.C. Stop (codes "0010" and "0011"), Run/Stop-Forward/Reverse Control
(Function No. 1.00) must be set to External Contacts (code "0001"). 5. The rate of change of
the "UP" Control for frequency setting, using external contacts, is proportional to the Accel
Time setting (Function No. 3.03). The incremental rate of change of the "DOWN" Control for
frequency setting, using external contacts, is proportional to the Decel Time Setting
(Function No. 3.04).
*Functions which can only be changed while the drive is in Stop Mode.