Controlled Products Systems Group PATRSL - Manual (Page 19)

17
DS2 Programming Switches
Factory settings are shown in bold italic type
1 Solenoid lock enable / Gate in operation indicator
ON Solenoid lock output energizes half second before gate begins to move and remains energized
until four seconds after reaching a limit (+12Vdc output 1.5 amp max)
OFF Solenoid lock / gate in operation indicator is inactive
2 Magnetic lock enable
ON Magnetic lock relay is active and will release half second before gate
begins to open (+12 vdc output 1.5 amp max)
OFF Magnetic lock relay is inactive
3 Security Shunt Circuit Enable / Open Gate Indicator
ON Security shunt circuit relay is active (closed circuit)(wire in parallel)
OFF Security shunt circuit relay is inactive (open circuit)
4 Motion Detector Enable
ON Activates motion detector input (if input is activated gate will not open)
OFF Disables motion detector input
Emergency Manual Release
Emergency manual release cover
Remove lock and rotate emergency manual release cover to the up position.
Pull manual release knob out (about ¾ inch)
Once knob has been pulled the gate can then be pushed by hand.
If knob cannot be pulled the gate may need to be agitated left or right.
To reset the knob push in on knob and roll gate until knob snaps in place. It may be
necessary to tap the knob inward to fully lock in place.
WARNING: Only insert hand into access hole as far as needed to grip the
release knob.
Trying to insert hand farther can result in injury .
Siren Output
OPEN/CLOSE
COMMAND
Vehicular Gate Operator
Gate Weight Max. Load: 650 lbs.
LED INDICATOR S2
RESET
Entrapment
S
E
C
U
R
I
T
Y S
H
U
N
T C
O
M
M
O
N
G
N
D M
A
G
L
O
C
K S
O
L
O
N
O
I
D
L
O
C
K C
O
M
M
O
N
G
N
D O
U
T
P
U
T
+
1
2
V
O
N
2
3
4
1 SOLONOID LOCK ENABLE
MAGNETIC LOCK ENABLE
SECURITY SHUNT ENABLE
MOTION DETECTOR ENABLE
15
5
0 10
TIMER TO CLOSE
ADJUSTMENT
Timer
ADJUSTMENT
Class I or Class II per UL325
J2 INDICATORS
1- +12V OUT 1.5 AMP MAX
2- COMMON
GROUND
3-
PUSH BUTTON INPUT
4- OPEN SAFETY EDGE
5- CLOSE INPUT
6-
SECONDARY ENTRAPMENT DEVICE INPUT
7- COMMON
GROUND
8-
STOP CIRCUIT INPUT N/C
9-
FREE EXIT / OPEN INPUT
10- UNDER GATE / CENTER LOOP INPUT
11- SAFETY LOOP / REVERSING EDGE INPUT
12-
MOTION DETECTOR INPUT
1 2 3 4 5 6 7 8 9 10 11 12
J2
BOTH ON FOR DUAL
DS1 SWITCH SETTINGS FACTORY SETTINGS
SW-1 AUTO CLOSE TIMER ENABLE OFF
SW-2 TIMER TO CLOSE WILL ACTIVATE ON LIMIT ONLY ON
SW-3 MASTER GATE ENABLE ON
SW-4 SLAVE GATE ENABLE OFF
SW-5 SOLENOID LOCK OPTION, SEE INSTALLATION MANUAL OFF
SW-6 SOFT STOP RETRACT ENABLE OFF
SW-7 SOFT STOP EXTEND ENABLE OFF
SW-8 STOP CIRCUIT ENABLE OFF
SW-9 OPERATING DIRECTION REVERSE OFF
SW-10 SOFT START ENABLE FOR SW6 AND SW7 OFF
1
2
3
4
5
6
7
8
9
10 O
N
DS1
PATRIOT CONTROL BOARD
USAutomatic MADE IN USA
CURRENT SENSE
ADJUSTMENT
0 10
5
MASTER
Sensitivity
CURRENT SENSE
ADJUSTMENT
0 10
5
SLAVE
Sensitivity
15