beautypg.com

Step 6 current sense adjustment – Controlled Products Systems Group PATRSL User Manual

Page 14

background image

12

Step 6

Current Sense Adjustment

The control board has two current sense adjustments, MASTER and SLAVE (see illustration 17). Dual gates
will require adjustment of both, adjust sensitivity so that the gate force required to sense an obstruction is at the
desired level.

Remember if the gate reverses direction when operating without contacting an obstruction, then minimizing
sensitivity (increase force) may be required. Do not increase more than necessary.

The adjustment has a maximum rotation of 1 turn, beginning at 0 and ending at 10. The factory setting is around
number 3. Do not force the adjustment past the stop points.

IMPORTANT NOTE:

Locate the current sense adjustments below. Notice that there are two adjustments MASTER and SLAVE.
We intentionally set the sensors at a highly sensitive setting. This may need to be adjusted to achieve gate
movement without tripping the sensitivity circuit and causing the gate to reverse direction. If the gate reverses
direction twice and then stops the control board will need to be reset.












STEP 7 Connecting Control Board / Battery to the Wiring Harness

Verify that the wiring harness is not connected to the control board. Install the battery into the backside of the
operator. Connect the wiring harness Red wire to the positive post of the battery and the black wire to the
negative post of the battery. Connect the wiring harness to the Master connector on the control board.

STEP 8 Operating the Gate (Keep hands away from moving parts)

Verify that the gate is in the half open position and no objects are in the path of the gate.
Locate the “Open / Close Command” pushbutton on the Patriot control board, this will be used to operate the
gate.

Press the “Open / Close Command” pushbutton to operate the gate. Gate should travel in the open direction if
all settings are correct. If gate reverses direction a current sense adjustment must be made (see step 6 above).

Once current sense adjustment is made press the “Open / Close Command” button again.

If gate travels past the desired stop position adjust the limit switches, see page 13.

Open / Close
Command
button

Secondary
Entrapment Siren
Red +12 vdc
Black Ground

Siren Output

OPEN/CLOSE
COMMAND

Vehicular Gate Operator

Gate Weight Max. Load: 650 lbs.

LED INDICATOR

S2

RESET

Entrapment

S
E
C
U
R
I
T
Y

S
H
U
N
T

C
O
M
M
O
N

G
N
D

M
A
G
L
O
C
K

S
O
L
O
N
O
I
D
L
O
C
K

C
O
M
M
O
N

G
N
D

O
U
T
P
U
T
+
1
2
V

O
N

2
3
4

1

SOLONOID LOCK ENABLE
MAGNETIC LOCK ENABLE
SECURITY SHUNT ENABLE
MOTION DETECTOR ENABLE

15

5

0

10

TIMER TO CLOSE

ADJUSTMENT

Timer

ADJUSTMENT

Class I or Class II per UL325

J2

INDICATORS

1-

+12V OUT 1.5 AMP MAX


2- COMMON

GROUND


3-

PUSH BUTTON INPUT


4-

OPEN SAFETY EDGE


5- CLOSE

INPUT


6-

SECONDARY ENTRAPMENT DEVICE INPUT


7- COMMON

GROUND


8-

STOP CIRCUIT INPUT N/C


9-

FREE EXIT / OPEN INPUT


10-

UNDER GATE / CENTER LOOP INPUT


11-

SAFETY LOOP / REVERSING EDGE INPUT


12-

MOTION DETECTOR INPUT

1

2

3

4

5

6

7

8

9 10 11 12

J2

BOTH ON FOR DUAL

DS1 SWITCH SETTINGS

FACTORY SETTINGS

SW-1

AUTO CLOSE TIMER ENABLE

OFF

SW-2

TIMER TO CLOSE WILL ACTIVATE ON LIMIT ONLY

ON

SW-3

MASTER GATE ENABLE

ON

SW-4

SLAVE GATE ENABLE

OFF

SW-5

SOLENOID LOCK OPTION, SEE INSTALLATION MANUAL

OFF

SW-6

SOFT STOP RETRACT ENABLE

OFF

SW-7

SOFT STOP EXTEND ENABLE

OFF

SW-8

STOP CIRCUIT ENABLE

OFF

SW-9

OPERATING DIRECTION REVERSE

OFF

SW-10

SOFT START ENABLE FOR SW6 AND SW7

OFF

1
2
3
4
5
6
7
8
9
10

O
N

DS1

PATRIOT CONTROL BOARD

USAutomatic

MADE IN USA

CURRENT SENSE
ADJUSTMENT

0

10

5

MASTER

Sensitivity

CURRENT SENSE
ADJUSTMENT

0

10

5

SLAVE

Sensitivity

15

Master
actuator
connector.
Slave

Illustration 17

Reset button

Current sense
adjustments
master and slave

5

10

0