Clear-Com FreeSpeak Antenna Splitter User Manual

Freespeak digital wireless

This manual is related to the following products:

FreeSpeak Antenna FreeSpeak Beltpack FreeSpeak Base Station FreeSpeak

Table of contents

Document Outline

Contents
Figures
Tables
Important Safety Instructions
- EMC and Safety
Getting Started: An Introduction to FreeSpeak
- FreeSpeak Features
- A FreeSpeak Communication System
  - Important Installation Information
    - System Password
    - Default Map
Quick Start
- Connecting the BaseStation
- Overview of Beltpack Operation
- Assigning Labels to the FreeSpeak BeltPacks
- Creating a Group
- Assigning the Group Label to FreeSpeak Beltpack Keys
- Calling the Group from the Beltpacks
- Calling the Group from the 4-Wire Audio Device
- Calling the Group from the Wired Party-Line Beltpack
- Creating a Wireless Party Line
- Assigning the Wireless Party Line Label to FreeSpeak Beltpack Keys
- Calling the Wireless Party Line from the Beltpacks
- Calling the Wireless Party Line from the 4-Wire Audio Device
- Calling the Wireless Party Line from the Wired Party-Line Beltpack
Operating The FreeSpeak Basestation
- Introduction
- Understanding Front-Panel Operation
Connecting The FreeSpeak Basestation
- Understanding the Back-Panel Connectors
- Connecting to Party-Line Intercom Systems
- Wireless Party Line
- Connecting to 4-Wire and Digital Matrix Intercom
- Connecting to a Program Audio Source
- IFB Configuration
- Connecting to the Stage Announce Output
- Connecting to a PC
  - Connecting Via the Serial Port
  - Connecting Via the LAN Port
- Connecting to Transceiver/Antennas (FS-TA)
Programming a System From the Basestation
- A Note About Terminology
- Using the Basestation’s Programming Menus
- Saving Changes
- Basestation Password
- Changing Beltpack Labels
- Setting and Changing Port Labels
- Setting and Changing Group Labels
- Adding Group Members
- Beltpacks
- Setting Input and Output Port Levels
  - Setting Port Call Destination
- Configuring a Party Line
- Basestation SYSTEM Menu
Operating The FreeSpeak Wireless BeltpacK
- Overview of the Wireless Belpack
  - Beltpack Top Control Section
  - Beltpack Front/Display Section
- Beltpack Batteries
- Accessing the Talk/Listen Paths on the FreeSpeak Beltpack
- Beltpack Menu Options
Programming at the Beltpack
- Introduction to Programming on the Beltpack
- Beltpack Programming - Menu Structure
- Main Programming Menu
- The Alarm Options Menu
- The Headphone Menu
  - Headset Noise Gate
- The Microphone Menu
- The Status (Information) Menu
- Adjust Contrast
- Set Factory Defaults
- Tap Latch
- Keylock
- PTT Configuration
- Master Volume Control
- Page Options
  - Page Locking
Operating The FreeSpeak transceiver/Ante nna
- Transceiver/Antenna (FS-TA)
- Transceiver/Antenna Splitter (PD2203)
Installing a System
- Placing the Basestation
- Placing the Antennas and Splitters
  - Wiring the Antennas and Splitters
  - Determining Coverage Areas
- Doing a Site Survey to Determine Coverage Areas
FreeSpeak Configuration Editor
- Introduction
- Loading and Saving Configurations
- Beltpacks tab
- Ports tab
- Groups tab
- Antennas tab
- IFB Tab
  - Configuring an IFB
- System Tab
FreeSpeak Toolkit
- Introduction
- Toolkit Installation
- Beltpack Registration
  - Entering beltpack serial numbers into the basestation
  - Entering the basestation system ID into the beltpack
- Basestation Serial Upgrader
  - Upgrading the basestation firmware
- Beltpack Serial Upgrader
  - Installing the Beltpack Upgader
  - Running the Beltpack Upgrader
- Basestation Programming Serial Cable Pinout
- Beltpack Programming Serial Cable Pinout
Specifications
- Notice about Specifications
Glossary
Appendix A: DECT Carrier Frequency Chart
Appendix B: Programming menus
Limited Warranty
Technical Support & Repair Policy
- TECHNICAL SUPPORT POLICY
- RETURN MATERIAL AUTHORIZATION POLICY
- REPAIR POLICY