Power save mode commands – Extron Electronics DSC HD-3G A User Guide User Manual
Page 61
Command
ASCII Command
(Host to Scaler)
Response
(Scaler to Host)
Additional Description
Output Configuration (continued)
HDMI Output Format (DSC 3G HD only)
Set format
E
X4*
VTPO
}
Vtpo
X4*
]
Set output format
X4*
for the
HDMI output.
View setting
E
VTPO
}
X4*
]
Show current HDMI output
format.
Power Save Mode
Power save off
E
0 PSAV
}
Psav 0
]
Set the DSC to run in full power
mode (default).
Power save on
E
1 PSAV
}
Psav 1
]
Place the DSC in low power
mode.
NOTE:: This mode can be exited only via the E 0 PSAV } command.
View setting
E
PSAV
}
X6@
]
In verbose modes 2 and 3:
Psav
X6@
]
View power save status
X6@
.
Screen Saver Mode (Takes place when no signal is detected on the input.)
Set screen saver mode
E
M
X4)
SSAV
}
Ssav M
X4)
]
Sets the screen saver mode to
X4)
(default = 1= black).
View mode
E
M SSAV
}
X4)
]
In verbose modes 2 and 3:
Ssav M
X4)
]
View current screen saver
mode
X4)
.
Set sync time out
duration
E
T
X2*
SSAV
}
Ssav T
X2*
]
Set the time before sync
timeout to
X2*
seconds.
Default = 501 seconds (never).
View sync timeout
duration
E
T SSAV
}
X2*
]
In verbose modes 2 and 3:
Ssav T
X2*
]
View amount of time
X2*
before
sync timeout.
View screen saver status
E
S SSAV
}
X6#
]
In verbose modes 2 and 3:
Ssav S
X6#
]
View the screen saver status
X6#
.
NOTE:
X2*
= Output sync timeout — 1 through 500, in 1-second increments (default = 501 seconds = never)
0 = The output sync is instantly disabled with no active input.
501 = Output sync never times out (default).
X4)
= Screen saver mode: 1 = black screen (default), 2 = blue output with OSD text
X4*
= HDMI output format:
0 = Auto (default). (HDMI – RGB Full to a CEA sink or DVI to a non-CEA sink). OSD reads Auto.)
1 = DVI (RGB 444, 0-255, no audio, no InfoFrames). OSD reads DVI RGB 444.)
2 = HDMI RGB Full (RGB 444, 0-255, audio, InfoFrames. OSD reads RGB Full.)
3 = HDMI RGB Limited (RGB 444, 16-235, audio, InfoFrames. OSD reads RGB Limited.)
4 = HDMI YUV Full (YUV 444, 0-255, audio, InfoFrames. OSD reads YUV 444 Full.)
5 = HDMI YUV Limited (YUV 444, 16-235, audio, InfoFrames. OSD reads YUV 444 Limited.)
6 = HDMI YUV Full (YUV 422, 0-255, audio, InfoFrames. OSD reads YUV 422 Full.)
7 = HDMI YUV Limited (YUV 422, 16-235, audio, InfoFrames. OSD reads YUV 422 Limited.)
X6@
= Power saver mode: 0 = full power mode (default), 1 = lower power mode
X6#
= Screen saver status:
0 = active input detected, timer not running
1 = No active input detected, timer running, output sync active
2 = No active input detected, timer expired, output sync disabled
DSC 3G-HD A and DSC HD-3G A • Remote Configuration and Control
55