Disc – Onkyo TX-NR1000 User Manual
Page 68
68
Enjoying Movies and Music in the Remote Zone (Zone 2/3)
—Continued
Operating with the Remote Controller
When operating with the remote controller, how to
operate depends on the location of Zone 2 or Zone 3, or
the distance from the TX-NR1000/TX-NR5000E.
• Point the remote controller at the infrared receiver on
the TX-NR1000/TX-NR5000E, and then operate the
controller.
• Install a remote controller sensor in Zone 2 or Zone 3
through an IR connection (See page 45).
• Switch the Transmission Signal Format to RF (Radio
Frequency) (depending on the destination) (See page
141).
Operating on the TX-NR1000/TX-NR5000E
1
Power on the devices in Zone 2 or Zone 3.
Press the [ZONE 2] or [ZONE 3] button, and
then the [ON] button.
2
Select a source.
Rotate the scroll wheel to select a source while
the [ZONE 2] or [ZONE 3] button is lighted (if
the button is not lighted, press the [ZONE2] or
[ZONE 3] button to light it).
• When you have selected the tuner, you can
choose a preset channel with the [CH DISC
+/–] button.
3
Adjust the volume level.
Press the [ZONE 2] (or [ZONE 3]) button, and
within 5 seconds, press the [LEVEL –/+] button
to adjust the volume level.
Notes:
• When the pre-main amplifier or receiver is
connected, the volume level should be adjusted
at the connected component side.
• When not using Zone 2 or Zone 3, press the
[ZONE 2] (or [ZONE 3]) button, and then
press the [STANDBY] button.
--/---
@. - ' /
ABC
DEF
PQRS
TUV
WXYZ
DIRECT TUNING
GHI
JKL
MNO
CAPS
DELETE
LANGUAGE LOCATION
ALBUM
AR TIST
GENRE
PLAYLIST
REPEAT
VIDEO
MUSIC
PHOTO
CUSTOM
DISPLAY
DIMMER
T V
INPUT
SLEEP
RANDOM
REC
MAIN A MAIN B
MUTING
ENTER
LAST M
ANGLE
SUBTITLE
AUDIO
MEMORY
SEARCH
A-B
REPEAT
ON
STANDBY
TV
TV CH
TV VOL
RC-
558M
SE
RVE
R
AUDIO
AD
J
EXIT
GU
ID
E
PREV
CH
+10
0
CLEAR
1
2
3
4
5
6
7
8
9
INPUT
TO
P M
ENU
MEN
U
SET
UP
RE
TURN
ZONE
2
INPUT
MODE
MACRO
VOL
CH
DISC
TEST TONE
CH SEL
PURE A
SURR
DIRECT
STEREO
Re-EQ
THX
ALL ST
LEVEL+
LEVEL-
L NIGHT
AUDIO SEL
DSP
DSP
+
-
+
-
I
ZONE
3
#
CH DISC +/–
ON, STANDBY
LEVEL –/+
ZONE 2
ZONE 3
1
Turn on the power supply to the
TX-NR1000/TX-NR5000E, and then select
a source for Zone 2 or Zone 3.
For Zone 2, press the [ZONE 2] button, and then
select the source with the [SELECT/PRESET] dial.
For Zone 3, press the [REC/ZONE 3] button, and
then, select the source with the [CONTROL/
TUNING] dial.
When you press the [ZONE 2] or [REC/ZONE 3]
button, the [STANDBY] indicator on the
TX-NR1000/TX-NR5000E blinks for five sec-
onds, so perform operations while it is blinking.
The source button for Zone 2 lights in green and
the source buttton for Zone 3 lights in red.
To switch the source for Zone 2 (or Zone 3) and
the main room simultaneously:
Repeatedly press the [ZONE 2] (or [REC/ZONE
3]) button to display “Z2Sel:SOURCE,” and then
select the source.
2
Adjust the volume level.
For Zone 2, press the [LEVEL] button under the
[ZONE 2] button, and then adjust with the
[SELECT/PRESET] dial.
For Zone 3, press the [LEVEL] button under the
[REC/ZONE 3] button, and then adjust with the
[CONTROL/TUNING] dial.
Notes:
• When a pre-main amplifier or receiver is
connected to the TX-NR1000/TX-NR5000E,
the volume level should be adjusted at the
connected component side.
STANDBY/ON
STANDBY
PURE AUDIO
MASTER VOLUME
OPEN
ZONE
2 (
)
GREEN
MAIN (
)
BLUE
REC / ZONE
3 (
)
RED
DISPLAY
DVD
VIDEO
3
VIDEO
4
VIDEO
5
VIDEO
6
VIDEO
7
VIDEO
2
VIDEO
1
MEMORY
SETUP
EXIT
PHONES
VIDEO
7 INPUT
S VIDEO
DIGITAL
AUDIO
VIDEO
L
R
LISTENING
MODE
AUDIO
SELECTOR
TONE
CLEAR
DIMMER
ZONE
2
REC/ ZONE
3
LEVEL
LEVEL
SELECT/ PRESET
CONTROL / TUNING
PUSH TO ENTER
PUSH TO ENTER
C D
NET AUDIO
PHONO
TUNER
TAPE
1
TAPE
2
TUNING
MODE
STANDBY/ON
REC/ZONE3
ZONE2
CONTROL / TUNING
SELECT/PRESET