Onkyo TX-NR1000 - Manual (Page 14)

14
Index Parts and Facilities —Continued
1 ( ) i.LINK S400 (AUDIO) terminals
Some of the Asian models are not equipped with the
i.LINK(AUDIO) terminals.
These connectors are for connecting to the i.LINK
(AUDIO)-ready device using a 4-pin (S400) i.LINK
(AUDIO) cable. The TX-NR1000/TX-NR5000E
complies with the standards on audio only
transimissions.
2 ETHERNET (Net-Tune)
This connector is for connecting to an Ethernet network.
3 DIGITAL OPTICAL IN/OUT
The input/output terminals for digital sound signal.
The sound quality equals the signal passed through
the COAXIAL terminals.
4 DIGITAL COAXIAL IN/OUT
The input/output terminals for digital sound signal.
The sound quality equals the signal passed through
the OPTICAL terminals.
5 MULTI-CH IN 1/2
This connector is for connecting components with a
multichannel output.
Two sets of multichannel input terminals are
available on the TX-NR1000/TX-NR5000E.
6 AUDIO IN/OUT
These connectors are for connecting to the audio
input and output jacks on audio/video components.
To connect a turntable, connect to the PH jacks.
In addition to the PH jacks, the TX-NR1000/
TX-NR5000E offers nine input and five output jacks.
7 VIDEO/S VIDEO IN/OUT
These connectors are for connecting to the video
input and output jacks on video components.
Six input and 4 output jacks are available for each
of VIDEO and S VIDEO connection.
8 COMPONENT VIDEO IN/OUT
These connectors are for connecting to the component
video outputs/inputs of video components that have them.
European and Asian models are equipped with three
inputs and one output for the RCA-type
COMPONENT connection and one input and
output for the BNC-type COMPONENT
connection.
For other than European and Asian models, there
are four inputs and two outputs for the RCA-type
COMPONENT connection.
Check the type of terminals or jacks on the device to
connect before making connections.
9 ANTENNA (FM/AM)
These jacks are for connecting the FM indoor
antenna and the AM loop antenna that are supplied
with the TX-NR1000/TX-NR5000E.
0 HDMI IN/OUT
This interface can transfer digital audio and video
signals simultaneously. The terminal can be
connected to the HDMI terminal on the components
such as DVD player, set top box (B tuner),
projector, and digital TV.
A REMOTE CONTROL
This jack is for connecting other Onkyo components
equipped with the same
terminal. The audio
connection cables must also be connected.
Rear Panel
E
GND
“Net-Tune”
is a trademark of
Onkyo Corporation.
ETHERNET
( Net-Tune )
A
REMOTE
CONTROL
MAIN
ZONE 3
ZONE 2
IN
AC INLET
A L
R
FRONT SURR SURR
BACK
CENTER SUB
WOOFER SUB
WOOFER
FRONT L CENTER FRONT R SURR BACK L (ASSIGNABLE) SURR R SURR L
FRONT R (BTL) FRONT L (BTL)
IR
12V
TRIGGER
OUT
RS 232
PRE OUT A ( SINGLE )
PRE
OUT B
C
E
200mA MAX.
100mA MAX.
100mA MAX.
100mA MAX.
100mA MAX.
AC 120V 60Hz
SWITCHED
120W 1A MAX.
AC OUTLET
UDC / UDT
SPEAKERS A
SPEAKERS B
2 2
1
6 6
5 5
4 4
3 3
2 2
1 1
OPTICAL COAXIAL
AUDIO IN
1
3
2
1
PH
2
3
9
8
7
6
5
4
4
5
R L
L R
L R
R L
G
IN 1
IN 2
HDMI
S VIDEO VIDEO
IN IN IN 1 IN 2
3
2
1 Y
P B
P R
COMPONENT VIDEO
IN 3
6
5
4 Y
P B
P R
2
1
4
3
Y
P B
P R
Y
P B
P R
COMPONENT VIDEO
IN 4
ANTENNA
FM
75
B
SURR BACK R (ASSIGNABLE)
A
B
D
DIGITAL IN DIGITAL IN L R
S VIDEO S VIDEO VIDEO VIDEO
OUT
MODEL NO. TX-NR 1000
C D
OUT OUT
F L
OUT
I H
OUT OUT
J K
OUT 1
OUT 2
AM
1
SBR SBL
SR SL
SUB C
FR FL
SBR SBL
SR SL
SUB C
FR FL
MULTI - CH
IN 1
MULTI - CH
IN 2
B
*
*This terminal is provided for future service enhancement and is not used currently. Never plug the cable connector for
other terminals into this terminal.