Connecting the power/basic operations, Turning on the power – Onkyo TX-NR1000 User Manual
Page 50
50
Connecting the Power/Basic Operations
• Before you plug in the TX-NR1000/TX-NR5000E, confirm that all connections have been made properly.
• Turning on the power may cause a momentary power surge, which might interfere with other electrical equipment
on the same circuit, such as computers. If this happens, use a wall outlet on a different circuit.
(All models other than USA, Canadian, and Australian models)
The TX-NR1000/TX-NR5000E is shipped with the main power (POWER) switch in the on position (
). When
the power cord is plugged in for the first time, the TX-NR1000/TX-NR5000E will automatically enter the standby
state and the [STANDBY] indicator will light (same condition after step 2 below on the left coloumn).
Note:
Any components connected via
will also be turned
on when the remote controller’s [ON] button is pressed.
ON
STANDBY/ON
STANDBY
PURE AUDIO
MASTER VOLUME
OPEN
ZONE
2 (
)
GREEN
MAIN (
)
BLUE
REC / ZONE
3 (
)
RED
DISPLAY
DVD
VIDEO
3
VIDEO
4
VIDEO
5
VIDEO
6
VIDEO
7
VIDEO
2
VIDEO
1
MEMORY
SETUP
EXIT
PHONES
VIDEO
7 INPUT
S VIDEO
DIGITAL
AUDIO
VIDEO
L
R
LISTENING
MODE
AUDIO
SELECTOR
TONE
CLEAR
DIMMER
ZONE
2
REC/ ZONE
3
LEVEL
LEVEL
SELECT/ PRESET
CONTROL / TUNING
PUSH TO ENTER
PUSH TO ENTER
C D
NET AUDIO
PHONO
TUNER
TAPE
1
TAPE
2
TUNING
MODE
OFF
ON
STANDBY/ON
STANDBY
PURE AUDIO
MASTER VOLUME
POWER
OPEN
ZONE
2 (
)
GREEN
MAIN (
)
BLUE
REC / ZONE
3 (
)
RED
DISPLAY
DVD
VIDEO
3
VIDEO
4
VIDEO
5
VIDEO
6
VIDEO
7
VIDEO
2
VIDEO
1
MEMORY
SETUP
EXIT
PHONES
VIDEO 7 INPUT
S VIDEO
DIGITAL
AUDIO
VIDEO
L
R
LISTENING
MODE
AUDIO
SELECTOR
TONE
CLEAR
RT/ PTY/ TP
ZONE
2
REC/ ZONE
3
LEVEL
LEVEL
SELECT/ PRESET
CONTROL / TUNING
PUSH TO ENTER
PUSH TO ENTER
C D
NET AUDIO
PHONO
TUNER
TAPE
1
TAPE
2
TUNING
MODE
STANDBY/ON
STANDBY/ON
POWER
MASTER VOLUME
MASTER VOLUME
(USA, Canadian, and Australian models)
(Other models)
STANDBY indicator
Input source buttons
To wall outlet
Input source buttons
STANDBY indicator
To wall outlet
Turning on the Power
1
Plug the power cord into an AC
wall outlet.
(USA, Canadian, and Australian
models)
The [STANDBY] indicator will light up.
(Other models)
Press the [POWER] switch to set
the TX-NR1000/TX-NR5000E to
standby state.
The [STANDBY] indicator will light up.
2
Press the [STANDBY/ON] button
to turn on the TX-NR1000/
TX-NR5000E.
The display will light up and the
[STANDBY] indicator will turn off.
If you press the [STANDBY/ON] button
again, the TX-NR1000/TX-NR5000E
returns to the standby state.
OFF
ON
STANDBY
POWER
STANDBY/ON
STANDBY
Turn off
Operating on the TX-NR1000/
TX-NR5000E
1
Select an input source.
Press the input source button.
*You cannot listen to a source in main
room A, and to another source in main
room B.
2
Start playing the device selected.
When playing a picture device such as a
DVD player, you need to switch input to
a monitor such a TV set.
Some picture-playing devices such as a
DVD-type game machine may also
require setting of sound output. Refer to
the manual of the device connected.
3
Adjust the volume level with the
[MASTER VOLUME] dial.
You can adjust the volume level in the
range from –
∞
, –81.5 dB to 18.0 dB
(Max) (when Relative is selected in the
Volume Setup sub-menu).
Hint:
TX-NR1000/TX-NR5000E is a product
for users to enjoy home theater, so it is
equipped with a wide range of volume
levels. Please fine tune the volume level
aaccording to your preferences.
DISPLAY
TAPE 1
TAPE 2
VIDEO
4
VIDEO
5
VIDEO
6
VIDEO
7
DVD
VIDEO
3
VIDEO
2
VIDEO
1
C D
NET AUDIO
PHONO
TUNER
MASTER VOLUME