Onkyo TX-NR1000 - Manual (Page 28)

28
Connecting Antennas
This chapter explains how to connect the supplied indoor
FM antenna and AM loop antenna, and how to connect
commercially available outdoor FM and AM antennas.
The supplied indoor FM antenna is for indoor use only.
If you cannot achieve good reception with the supplied
indoor FM antenna, try using a commercially available
outdoor FM antenna instead.
The supplied indoor AM loop antenna is for indoor use
only.
If you cannot achieve good reception with the supplied
indoor AM loop antenna, try using a commercially
available outdoor AM antenna.
Connecting the Indoor FM Antenna
1 Attach the FM antenna, as shown.
■ USA and Canadian Model
■ Other Models
Once your TX-NR1000/TX-NR5000E is ready
for use, you’ll need to tune into an FM radio
station and adjust the position of the FM antenna
to achieve the best possible reception.
2 Use thumbtacks or something similar to
fix the FM antenna into position.
Caution: Be careful that you don’t injure
yourself when using thumbtacks.
E
REMOTE
CONTROL
MAIN
ZONE 3
ZONE 2
IN
AC INLET A L
R
FRONT SURR SURR
BACK
CENTER SUB
WOOFER SUB
WOOFER
FRONT L CENTER FRONT R SURR BACK L (ASSIGNABLE) SURR R SURR L
FRONT R (BTL) FRONT L (BTL)
IR
12V TRIGGER OUT
RS 232
PRE OUT A (SINGLE)
PRE OUT B
C
E
200mA MAX.
100mA MAX.
100mA MAX.
100mA MAX.
100mA MAX.
AC 120V 60Hz SWITCHED 120W 1A MAX.
AC OUTLET
UDC / UDT
SPEAKERS A
SPEAKERS B
2 2
1
6 6
5 5
4 4
3 3
2 2
1 1
OPTICAL COAXIAL AUDIO IN
1
3
2
1
PH
2
3
9
8
7
6
5
4
4
5
R L
L R
L R
R L
G
IN 1
IN 2
HDMI, the HDMI logo
is a trademark
or registered
trademarks of HDMI
Licensing LLC.
HDMI S VIDEO VIDEO IN IN IN 1 IN 2
3
2
1 Y
PB
PR
COMPONENT VIDEO
IN 3
6
5
4 Y
PB
PR
2
1
4
3
Y
PB
PR
Y
PB
PR
COMPONENT VIDEO
IN 4 ANTENNA
FM
75
B
SURR BACK R (ASSIGNABLE)
A
B
D
DIGITAL IN DIGITAL IN L R
S VIDEO S VIDEO VIDEO VIDEO OUT C D F G H I J K L
MODEL NO. TX-NR 1000
C D
OUT OUT
F L
OUT
I H
OUT OUT
J K
A B
OUT 1
OUT 2
AM
1
“Net-Tune”
is a trademark of
Onkyo Corporation.
ETHERNET (Net-Tune)
SBR SBL
SR SL
SUB C
FR FL
SBR SBL
SR SL
SUB C
FR FL MULTI - CH
IN 1
MULTI - CH
IN 2
GND
FM antenna connector
AM antenna push terminals
FM
75 Insert the plug fully
into the socket.
FM
75 Insert the plug fully
into the socket
Thumbtacks, etc.
Connecting the AM Loop Antenna
1 Assemble the AM loop antenna, inserting
the tabs into the base, as shown.
2 Connect both wires of the AM loop
antenna to the AM push terminals, as
shown.
(The antenna’s wires are not polarity sensitive, so
they can be connected in either terminal)
Make sure that the wires are attached securely
and that the push terminals are gripping the bare
wires, not the insulation.
Once your TX-NR1000/TX-NR5000E is ready
for use, you’ll need to tune into an AM radio
station and adjust the position of the AM antenna
to achieve the best possible reception. Keep the
antenna as far away as possible from your
TX-NR1000/TX-NR5000E, TV, speaker cables,
and power cords.
AM
Push Insert wire Release