Onkyo TX-NR1000 - Manual (Page 101)

101
Listening Mode Setup —Continued
• When the impedance setting for “Front L/R A” or
“Front L/R B” in the Speaker Impedance sub-menu is
set to “6 ohms” or “4 ohms,” the available options will
be “A” and “B.”
A (Default): Outputs the source from the speakers
connected to the FRONT L/R SPEAKERS A terminals.
B: Outputs the source from the speakers connected to
the FRONT L/R SPEAKERS B terminals.
A+B: Outputs the source from the speakers connected
to the FRONT L/R SPEAKERS A and FRONT L/R
SPEAKERS B terminals. Note that this option is not
available when the front speakers are in Bi-amp or in
BTL configuration.
c. Subwoofer
This option configures the subwoofer to use when
playing the source in the Stereo listening mode. Select
the terminal to which the subwoofer you want to use is
connected. This setting can be made when the
“(Speaker A) Subwoofer” is set to an option other than
“Not Used” in the Speaker Configuration sub-menu.
However, when the “(Speaker B) Subwoofer” is set to
an option other than “Main A” in the Speaker
Configuration sub-menu, the available options will be
“A” or “Not Used.”
A (Default): Outputs the source only from the
subwoofer connected to the SUBWOOFER PRE OUT
A terminal.
B: Outputs the source only from the subwoofer
connected to the SUBWOOFER PRE OUT B terminal.
A+B: Outputs the source from the subwoofers
connected to the SUBWOOFER PRE OUT A and
SUBWOOFER PRE OUT B terminals.
Not Used: No subwoofers are used for playback.
This sub-menu allows you to configure the audio effect
and playback options when you play a source in the
Direct or Pure Audio listening mode.
a. Front Speaker
This option configures the front speakers to use when
playing the source in the Direct or Pure Audio listening
mode. Select the speaker terminals to which the
speakers you want to use are connected. This setting can
be made when the “(Speaker B) Front L/R” is set to
“Main A” in the Speaker Configuration sub-menu.
• When the impedance setting for “Front L/R A” or
“Front L/R B” in the Speaker Impedance sub-menu is
set to “6 ohms” or “4 ohms,” the available options will
be “A” and “B.”
A (Default): Outputs the source from the speakers
connected to the FRONT L/R SPEAKERS A terminals.
B: Outputs the source from the speakers connected to
the FRONT L/R SPEAKERS B terminals.
A+B: Outputs the source from the speakers connected
to the FRONT L/R SPEAKERS A and FRONT L/R
SPEAKERS B terminals. Note that this option is not
available when the front speakers are in Bi-amp or in
BTL configuration.
b. Center Speaker
This option configures the center speaker to use when
playing the source in the Direct or Pure Audio listening
mode. Select the speaker terminal to which the speaker
you want to use is connected. This setting can be made
when the “(Speaker B) Center” is set to “Main A” in the
Speaker Configuration sub-menu.
• When the impedance setting for “Center A” or
“Center B” in the Speaker Impedance sub-menu is set
to “6 ohms” or “4 ohms,” the available options will be
“A” and “B.”
A (Default): Outputs the source from the speaker
connected to the CENTER SPEAKERS A terminal.
B: Outputs the source from the speaker connected to the
CENTER SPEAKERS B terminal.
A+B: Outputs the source from the speakers connected
to the CENTER SPEAKERS A and CENTER
SPEAKERS B terminals.
c. Surr L/R Sp
This option configures the surround speakers to use
when playing the source in the Direct or Pure Audio
listening mode. Select the speaker terminals to which
the speakers you want to use are connected. This setting
can be made when the “(Speaker B) Surr L/R” is set to
“Main A” in the Speaker Configuration sub-menu.
• When the impedance setting for “Surr L/R A” or “Surr
L/R B” in the Speaker Impedance sub-menu is set to
“6 ohms” or “4 ohms,” the available options will be
“A” and “B.”
A (Default): Outputs the source from the speakers
connected to the SURR L/R SPEAKERS A terminals.
B: Outputs the source from the speakers connected to
the SURR L/R SPEAKERS B terminals.
A+B: Outputs the source from the speakers connected
to the SURR L/R SPEAKERS A and SURR L/R
SPEAKERS B terminals.
d. Surr Bk Speaker
This option configures the surround back speakers to
use when playing the source in the Direct or Pure Audio
listening mode. Select the speaker terminals to which
the speakers you want to use are connected. This setting
can be made when the “(Speaker B) Surr Back” is set to
“Main A” in the Speaker Configuration sub-menu.
However, when the “(Speaker A) Surr Back” is set to
“BTL for Front,” “Bi-Amp for Front,” or “Not Used,”
this setting will not be displayed.
• When the impedance setting for “Surr L/R A” or “Surr
L/R B” in the Speaker Impedance sub-menu is set to
“6 ohms” or “4 ohms,” the available options will be
“A” and “B.”
Direct, Pure Audio Setup Sub-menu