Onkyo TX-NR1000 - Manual (Page 114)

114
Listening Mode Setup —Continued
B: Outputs the source only from the subwoofer
connected to the SUBWOOFER PRE OUT B terminal.
A+B: Outputs the source from the subwoofers
connected to the SUBWOOFER PRE OUT A and
SUBWOOFER PRE OUT B terminals.
Not Used: No subwoofers are used for playback.
This sub-menu allows you to configure the audio effect
and playback options when you play a source in the
Onkyo original listening mode. The settings in this sub-
menu can be made when the (Speaker A) Surr L/R
setting is set to an option other than “Not Used” in the
Speaker Configuration sub-menu.
a. Front Effect
This option allows you to turn off the reverb for the
front speakers. This is useful when playing live material
that already contains live reverberation as the added
reverb simply blurs the original sound. When the Front
Effect is turned off, no reverb is added to the front left,
front right, and center speakers and the original
reverberation can be heard as it is.
On (Default): The Front Effect is turned on and the
reverb is added.
Off: The Front Effect is turned off.
b. Reverb Level
This option allows you to adjust the amount of reverb to
suit your listening environment, source material, and so
on. The available settings are Small, Mid, and Large.
The option defaults to “Mid.”
c. Reverb Time
This option allows you to adjust the reverb time to suit
your listening environment, source material, and so on.
The available settings are Short, Mid, and Long. The
option defaults to “Mid.”
d. Front Speaker
This option configures the front speakers to use when
playing the source. Select the speaker terminals to
which the speakers you want to use are connected. This
setting can be made when the “(Speaker B) Front L/R”
is set to “Main A” in the Speaker Configuration sub-
menu.
• When the impedance setting for “Front L/R A” or
“Front L/R B” in the Speaker Impedance sub-menu is
set to “6 ohms” or “4 ohms,” the available options will
be “A” and “B.”
A (Default): Outputs the source from the speakers
connected to the FRONT L/R SPEAKERS A terminals.
B: Outputs the source from the speakers connected to
the FRONT L/R SPEAKERS B terminals.
A+B: Outputs the source from the speakers connected
to the FRONT L/R SPEAKERS A and FRONT L/R
SPEAKERS B terminals. Note that this option is not
available when the front speakers are in Bi-amp or in
BTL configuration.
e. Center Speaker
This option configures the center speaker to use when
playing the source. Select the speaker terminal to which
the speaker you want to use is connected. This setting
can be made when the “(Speaker B) Center” is set to
“Main A” in the Speaker Configuration sub-menu.
• When the impedance setting for “Center A” or
“Center B” in the Speaker Impedance sub-menu is set
to “6 ohms” or “4 ohms,” the available options will be
“A” and “B.”
A (Default): Outputs the source from the speaker
connected to the CENTER SPEAKERS A terminal.
B: Outputs the source from the speaker connected to the
CENTER SPEAKERS B terminal.
A+B: Outputs the source from the speakers connected
to the CENTER SPEAKERS A and CENTER
SPEAKERS B terminals.
f. Surr L/R Sp
This option configures the surround speakers to use
when playing the source. Select the speaker terminals to
which the speakers you want to use are connected. This
setting can be made when the “(Speaker B) Surr L/R” is
set to “Main A” in the Speaker Configuration sub-menu.
• When the impedance setting for “Surr L/R A” or “Surr
L/R B” in the Speaker Impedance sub-menu is set to
“6 ohms” or “4 ohms,” the available options will be
“A” and “B.”
A (Default): Outputs the source from the speakers
connected to the SURR L/R SPEAKERS A terminals.
B: Outputs the source from the speakers connected to
the SURR L/R SPEAKERS B terminals.
A+B: Outputs the source from the speakers connected
to the SURR L/R SPEAKERS A and SURR L/R
SPEAKERS B terminals.
g. Surr Bk Speaker
This option configures the surround back speakers to use
when playing the source. Select the speaker terminals to
which the speakers you want to use are connected. This
setting can be made when the “(Speaker B) Surr Back” is
set to “Main A” in the Speaker Configuration sub-menu.
However, when the “(Speaker A) Surr Back” is set to
“BTL for Front,” “Bi-Amp for Front,” or “Not Used,” this
setting will not be displayed.
• When the impedance setting for “Surr L/R A” or “Surr
L/R B” in the Speaker Impedance sub-menu is set to
“6 ohms” or “4 ohms,” the available options will be
“A” and “B.”
Mono Movie Setup/Enhance Setup/
Orchestra Setup/Unplugged Setup/
Studio-Mix Setup/TV Logic Setup
Sub-menu