Roland RG-1 - Manual (Page 8)

6
IMPORTANT NOTES
559b
• When you need to transport the unit, pack it in shock-
absorbent material. Transporting the unit without doing
so can cause it to become scratched or damaged, and
could lead to malfunction.
560
• Do not apply undue force to the music stand while it is in
use.
562
• Some connection cables contain resistors. Do not use
cables that incorporate resistors for connecting to this unit.
The use of such cables can cause the sound level to be
extremely low, or impossible to hear. For information on
cable specifications, contact the manufacturer of the cable.
565
• Before opening or closing the keyboard lid, always make
sure that no pets or other small animals are located on top
of the instrument (in particular, they should be kept away
from the keyboard and its lid). Otherwise, due to the
structural design of this instrument, small pets or other
animals could end up getting trapped inside it. If such a
situation is encountered, you must immediately switch off
the power and disconnect the power cord from the outlet.
You should then consult with the retailer from whom the
instrument was purchased, or contact the nearest Roland
Service Center.
Handling Floppy Disks
651
• Floppy disks contain a plastic disk with a thin coating of
magnetic storage medium. Microscopic precision is
required to enable storage of large amounts of data on
such a small surface area. To preserve their integrity,
please observe the following when handling Floppy disks:
• Never touch the magnetic medium inside the disk.
• Do not use or store Floppy disks in dirty or dusty
areas.
• Do not subject Floppy disks to temperature extremes
(e.g., direct sunlight in an enclosed vehicle). Recom-
mended temperature range: 10 to 50˚C (50 to 122˚F).
• Do not expose Floppy disks to strong magnetic fields,
such as those generated by loudspeakers.
652
• Floppy disks have a “write protect” tab which can protect
the disk from accidental erasure. It is recommended that
the tab be kept in the PROTECT position, and moved to
the WRITE position only when you wish to write new
data onto the disk.
fig.DiskProtect.e.eps
653
• The identification label should be firmly affixed to the
disk. Should the label come loose while the disk is in the
drive, it may be difficult to remove the disk.
654
• Store all disks in a safe place to avoid damaging them, and
to protect them from dust, dirt, and other hazards. By
using a dirty or dust-ridden disk, you risk damaging the
disk, as well as causing the disk drive to malfunction.
Handling the CDs (CD-ROMs)
Add
• When handling the discs, please observe the following.
• Do not touch the encoded surface of the disc.
• Do not use in dusty areas.
• Do not leave the disc in direct sunlight or an enclosed
vehicle.
801
• Avoid touching or scratching the shiny underside
(encoded surface) of the disc. Damaged or dirty CD-ROM
discs may not be read properly. Keep your discs clean
using a commercially available CD cleaner.
Add
• Keep the disc in the case.
Add
• Do not keep the disc in the CD drive for a long time.
Add
• Do not put a sticker on the label of the disc.
Add
• Wipe the disc with a soft and dry cloth radially from
inside to outside. Do not wipe along circumference.
Add
• Do not use benzine, record cleaner spray or solvents of
any kind.
Add
• Do not bend the disc. Bending discs may prevent proper
reading and writing of data, and may further result in
malfunction.
Using USB Memory
704 (edit)
• When connecting USB memory, make sure to press it until
it is fully inserted.
705 (edit)
• Never touch the terminals of the USB memory. Also,
avoid getting the terminals dirty.
708
• USB memory is constructed using precision components;
handle the cards carefully, paying particular note to the
following.
• To prevent damage to the USB memory from static
electricity, be sure to discharge any static electricity
from your own body before handling the USB
memory.
• Do not touch or allow metal to come into contact with
the contact portion of the USB memory.
• Do not bend, drop, or subject USB memory to strong
shock or vibration.
• Do not keep USB memory in direct sunlight, in closed
vehicles, or other such locations.
• Do not allow USB memory to become wet.
• Do not disassemble or modify the USB memory.
Add
• Insert the USB memory in the External Memory connector
evenly and without undue force. Forcing the USB memory
may damage the External memory connector.
Add
• Do not insert any object other than the USB memory (e.g.,
wires, coins, other types of disks, etc.) in the External
Memory connector. This may damage the External
Memory connector.
Add
• Do not subject the connected USB memory to excessive
stress.
Add
• Close the USB memory cover when using the USB
memory for extended periods.
Rear side of the disk
Write
(can write new data onto disk)
Protect
(prevents writing to disk)
Write Protect Tab
RG-1_e.book 6 ページ ２００８年４月８日 火曜日 午後２時３６分