Roland X-6 - Manual (Page 230)

230
Settings Common to All Modes (System Function)
Output Gain
This adjusts the output gain from the Fantom-X’s Analog Out and
Digital Out. When, for example, there are relatively few voices being
sounded, boosting the output gain can let you attain the most
suitable output level for recording and other purposes.
Value: -12–+12
Mix/Parallel
Specifies how the sound of the entire Fantom-X will be output.
Value
MIX: Set this to have the collective output of all sounds output from
the OUTPUT A (MIX) jacks. When you want to check the final
overall sound being output, set to MIX.
Sounds which are set in the respective Output Assign to be
output from the INDIVIDUAL 3 jack are output from the left
OUTPUT A (MIX) jack; sounds which are set to be output from
the INDIVIDUAL 4 jack are output from the right OUTPUT A
(MIX) jack.
Sounds output from the PHONES jack are the same as those
output from the OUTPUT A (MIX) jacks. Therefore, any sounds
set with Output Assign to be output from the OUTPUT B jacks
is not output from the PHONES jack. Be sure to have any sound
you want to hear through the headphones set to “MIX.”
PARALLEL: Output according to each Output Assign settings.
Master Key Shift
Shifts the overall pitch of the Fantom-X in semitone steps.
Value: -24– +24
Patch Remain (Patch Remain Switch)
Specifies whether currently sounding notes will continue sounding
when another patch or rhythm set is selected (ON), or not (OFF).
Also, when this is “ON,” changes produced by incoming MIDI
messages such as Volume or Pan (CC 5, 7, 10, 65, 68, 71–74, RPN 0, 1,
2, MONO ON, POLY ON), as well as tonal quality and volume
changes produced by the various controllers will be inherited.
Value: OFF, ON
Effects settings change as soon as you switch to a new patch or
rhythm set, without being influenced by the Patch Remain
setting. Because of this, certain effects settings can cause notes
that were until then sounding to no longer be heard, even
though Patch Remain has been set to on.
Device ID (Device ID Number)
When you want to transmit or receive System Exclusive messages,
set this parameter to match the Device ID number of the other MIDI
device.
Value: 17–32
Performance Control Channel
Performance Ctrl Ch selects the MIDI receive channel used during
switching of performances when MIDI messages (Program Change/
Bank Select) are sent from an external MIDI device. Set this to “OFF”
if performances are not to be switched from an external MIDI device.
Value: 1–16, OFF
If only a program change is received, and if the Performance
Ctrl Ch parameter setting coincides with the MIDI receive
channel of a part, priority will be given to switching the
performance.
Kbd Patch Rx/Tx Ch (Keyboard Patch Receive/
Transmit Channel)
Specifies the channel used to transmit and receive MIDI messages
for the Keyboard part in Patch mode.
Value: 1–16
Pad Patch Rx/Tx Ch (Pad Patch Receive/
Transmit Channel)
Specifies the channel used to transmit and receive MIDI messages
for the Pad part in Patch mode.
Value: 1–16
Transmit Program Change (Transmit Program
Change Switch)
Specifies whether Program Change messages will be transmitted
(ON) or not (OFF).
Value: OFF, ON
Transmit Bank Select (Transmit Bank Select
Switch)
Specifies whether Bank Select messages will be transmitted (ON) or
not (OFF).
Value: OFF, ON
Transmit Active Sensing (Transmit Active
Sensing Switch)
Specifies whether Active Sensing messages will be transmitted (ON)
or not (OFF).
Value: OFF, ON
Transmit Edit Data (Transmit Edit Data Switch)
Specify whether changes you make in the settings of a patch,
performance will be transmitted as system exclusive messages (ON),
or will not be transmitted (OFF).
Value: OFF, ON
MIDI
Fantom-X678_r_e.book 230 ページ ２００７年３月２０日 火曜日 午前１０時２０分