Konica Minolta bizhub 750 - Manual (Page 443)

12 Utility
12-30 bizhub 750/600
Utility
Ch
ap
te
r 12
Finisher
Adjust-
ment Center
Staple
Position The stapling position when printing with
the “Fold & Staple” function can be ad-
justed in 0.1 mm increments.
(FS-602)
–
12.8 to 12.7 mm:
0.0 mm
Half-Fold
Position The center folding position when printing
with the “Fold & Staple” function can be
adjusted in 0.1 mm increments.
(FS-602)
–
12.8 to 12.7 mm:
0.0 mm
Punch Ad-
justment Adjust the positions of the punched
holes.
• Punch Vertical Position: The vertical
position of the punched holes can be
adjusted in 0.1 mm increments for
each paper size. (PK-505)
• Punch Horizontal Position: The hori-
zontal position of the punched holes
can be adjusted in 0.1 mm incre-
ments. (PK-505)
• Punch Unit Vert. Position: The vertical
position of the punched holes can be
adjusted in 0.1 mm increments for
each paper size. (ZU-602)
• Punch Unit Hor. Position: The hori-
zontal position of the punched holes
can be adjusted in 0.1 mm incre-
ments. (ZU-602)
• Punch Resist Loop Size: The hole-
punching shift for double-sided print-
ing and outputting cover pages can
be adjusted in 0.8 mm increments.
(PK-505, ZU-602)
Punch Vertical Position:
–
5.0 to 5.0 mm: 0.0 mm
Punch Horizontal Posi-
tion: –5.0 to 5.0 mm:
0.0 mm
Punch Unit Vert. Posi-
tion: –5.0 to 5.0 mm:
0.0 mm
Punch Unit Hor. Posi-
tion: –5.0 to 5.0 mm: 0.0
mm
Punch Regist Loop Size:
Machine (Reverse Out-
put, ADU Output): –16.0
to 16.0 mm: 0.0 mm
PI (Uppre tray, Lower
tray): –16.0 to 16.0 mm:
0.0 mm
Z-Fold Po-
sition Ad-
justment The folding position for zigzag folding (Z-
Fold) can be adjusted for each paper
size.
• 1st Z-Folded Position: The position of
the first fold can be adjusted in 0.1
mm increments.
• 2nd Z-Folded Position: The position
of the second fold can be adjusted in
0.1 mm increments.
(ZU-602 or PK-505+ZU-602)
1st Z-Folded Position:
– 12.8 to +12.7 mm:
0.0 mm
2nd Z-Folded Position:
–
12.8 to +12.7 mm:
0.0 mm
Tri-Fold
Position The folding positions when using the
“Tri-Fold” setting can be adjusted in 0.1
mm increments.
(FS-602 or PK-505+ZU-602)
–
12.8 to +12.7 mm:
0.0 mm
2 Position
Staple The distance between the two staples
can be adjusted in 0.1 mm increments.
• Staple
• Corner Staple & Fold
(FS-602) 128 to 160 mm: 128 mm
Cover
Sheet Tray
Size Adjust the cover sheet tray size if the pa-
per cannot be detected correctly or if
one side of the cover sheet feeder is ad-
justed.
(PI-501) —
Parameter Description Settings (Default set-
tings are underlined.)