KEPCO MST Series User Manual
Operator’s manual, Kepco
Table of contents
Document Outline
- SECTION 1 - INTRODUCTION
- SECTION 2 - INSTALLATION
- SECTION 3 - OPERATION
- FIGURE 1-1. MST Power Supply
- SECTION 1 - INTRODUCTION
- 1.1 Scope of Manual
- 1.2 Description
- TABLE 1-1. MST Model Parameters
- 1.3 Specifications
- TABLE 1-2. MST General Specifications
- 1.4 Features
- 1.4.1 Control/Programming
- FIGURE 1-2. MST Power Supply, Mechanical Outline Drawing
- FIGURE 1-3. Remotely Controlled Power Supply Configurations Using Kepco Products
- 1.4.2 Status Indicators
- 1.4.3 Front Panel Meters
- 1.4.4 Output Enable/Disable and Polarity Reversal
- 1.4.5 Protection
- 1.4.6 Series Configurations
- 1.4.7 Parallel Configuration
- 1.5 Options
- 1.6 Accessories
- TABLE 1-3. Accessories
- SECTION 2 - INSTALLATION
- 2.1 Unpacking and Inspection
- 2.2 Terminations and Controls
- TABLE 2-1. Functions of Internal Controls
- 2.3 A-C Input Requirement
- 2.4 Cooling
- TABLE 2-2. Front Panel Controls and Indicators
- FIGURE 2-1. Front and Rear Views of the MST Power Module
- TABLE 2-3. Rear Terminations
- 2.5 Preliminary Check-out
- 2.5.1 Required Equipment
- 2.5.2 Initial Setup
- FIGURE 2-2. DC Output Connector Configuration for Preliminary Checkout
- FIGURE 2-3. Initial Checkout Setup
- 2.5.3 Checkout Procedure
- 2.6 Installation/Removal
- 2.6.1 Changing Control Bus Address (Node or Channel Number)
- TABLE 2-4. Node Address Selection
- FIGURE 2-4. Configuration and Calibration Controls and Testpoints
- 2.6.2 Installation
- 2.6.3 Removal
- 2.7 Grounding
- 2.7.1 Safety Grounding
- 2.7.2 D-C (Output) Grounding
- 2.8 Power Module to Load Interface
- FIGURE 2-5. Output Impedance vs. Frequency
- 2.9 Connection, General
- TABLE 2-5. DC Output Connector Pin Designations
- 2.9.1 Load Connection with Local Error Sensing
- 2.9.2 Load Connection with Remote Error Sensing
- FIGURE 2-6. Connector Locations and Pin Assignments
- SECTION 3 - OPERATION
- 3.1 Introduction to Controlling the MST Power Module Output
- 3.1.1 Status Flags (Error Messages)
- TABLE 3-1. Error Messages
- 3.1.2 Timing Requirements for a Valid Status
- 3.2 Operating Modes
- 3.2.1 Voltage Mode
- 3.2.2 Current Mode
- 3.3 Output Polarity Reversal
- TABLE 3-2. Maximum External Capacitance Values to Ensure Dry Switching
- 3.4 Output Enable and Disable
- 3.5 Parallel Operation
- 3.6 Series Operation
- 3.7 Fault Protection
- 3.7.1 Fault Recovery
- 3.7.2 Tracking Overvoltage and Overcurrent Detectors
- 3.7.3 Overtemperature Detectors
- 3.7.4 A-C Loss Detector
- 3.7.5 Open Sense/Power Wire Protection
- 3.8 Calibration
- 3.8.1 Equipment Required
- FIGURE 3-1. Calibration Test Set-up
- 3.8.2 +5 Volts Reference Adjust (R49)
- 3.8.3 Output Voltage (EO) Zero Adjust (R11)
- 3.8.4 Current Sense Zero Adjust (R50)
- 3.8.5 Output Current IO Zero Adjust (R51)
- 3.8.6 Voltage Reference Adjust (R47)
- 3.8.7 Current Reference Adjust (R48)
- 3.8.8 Current (IO) Full Scale Adjust (R52)