Enterasys Networks 8000/8600 User Manual
Enterasys Networks Hardware
Table of contents
Document Outline
- Title
- Notice
- Contents
- About this Guide
- Features Overview
- Specifications
- Features
- Hardware Overview
- Chassis
- Backplane
- Fan Module
- Control Modules
- AC Power Supply
- DC Power Supply
- Switching Fabric Module (XPedition8600 only)
- Line Cards
- SSR-ARE
- SSR-ATM29-02
- SSR-CM2B-64, SSR-CM3-128, and SSR-CM4-256
- SSR-FDDI-02
- SSR-GLX39-02
- SSR-GLX39-04 and SSR-GSX31-04
- SSR-GLX70-01-AA and SSR-GLH39-02
- SSR-GSX21-02-AA and SSR-GLX29-02-AA
- SSR-GSX31-02
- SSR-GTX32-04 and SSR-GTX32-02
- SSR-HFX21-08-AA and SSR-HFX29-08-AA
- SSR-HSSI-02-CK
- SSR-HTX22-08-AA and SSR-HTX12-08-AA
- SSR-HTX32-16
- SSR-POS29-04 and SSR-POS21-04
- SSR-POS39-02 and SSR-POS31-02
- SSR-SERCE-04-AA and SSR-SERC-04-AA
- Hardware Installation
- Safety Considerations
- Hardware Specifications
- Installing the Hardware
- Verifying Your Shipment
- Installing the Chassis
- Installing an AC Power Supply
- Installing a DC Power Supply
- Installing the Control Module
- Installing a Memory Upgrade
- Installing the Switching Fabric Module (XPedition8600 only)
- Installing Line Cards
- CLI Setup
- Proper Boot sequence
- Common Errors
- Helpful CLI Commands for Debugging
- Default Module Settings
- Preparing the Module
- Proper Boot Sequence
- Common Errors
- Helpful CLI Commands for Debugging
- Preparing the Module
- Proper Boot Sequence
- Common Errors
- Helpful CLI Commands for Debugging
- Preparing the Module
- Default Module Settings
- CLI Setup
- Proper Boot Sequence
- Common Errors
- Helpful CLI Commands for Debugging
- Default Module Settings
- CLI Setup
- Proper Boot Sequence
- Common Errors
- Helpful CLI Commands for Debugging
- CLI Setup
- Proper Boot Sequence
- Common Errors
- Helpful CLI Commands for Debugging
- CLI Setup
- Proper Boot Sequence
- Common Errors
- Helpful CLI Commands for Debugging
- CLI Setup
- Proper Boot Sequence
- Common Errors
- Helpful CLI Commands for Debugging
- CLI Setup
- Proper Boot Sequence
- Common Errors
- Helpful CLI Commands for Debugging
- CLI Setup
- Proper Boot Sequence
- Common Errors
- Helpful CLI Commands for Debugging
- Handling the Module
- Instructions
- Installing FPHYs
- Installing the ATM PHY Cards
- Software Installation andSetup
- Installing a PCMCIA Flash Card
- Powering On and Booting the Software
- Starting the Command Line Interface
- Setting Basic System Information
- Setting Up SNMP Community Strings
- Setting Up Passwords
- Setting the DNS Domain Name and Address
- Setting SYSLOG Parameters
- Loading System Image Software
- Loading Boot Firmware
- Activating Configuration Changes and Saving the Configuration File
- Troubleshooting
- Hardware Components
- SSR-ATM29-02
- SSR-CM2B-64, SSR-CM3-128, and SSRCM4-256
- SSR-FDDI-02
- SSR-GLX39-02
- SSR-GLX39-04 and SSR-GSX31-04
- SSR-GLX70-01-AA and SSR-GLH39-02
- SSR-GSX21-02-AA and SSR-GLX29-02-AA
- SSR-GSX31-02
- SSR-GTX32-04 and SSR-GTX32-02
- SSR-HFX21-08-AA and SSR-HFX29-08-AA
- SSR-HSSI-02-CK
- SSR-HTX22-08-AA and SSR-HTX12-08-AA
- SSR-HTX32-16
- SSR-POS29-04 and SSR-POS21-04
- SSR-POS39-02 and SSR-POS31-02
- SSR-SERCE-04-AA and SSR-SERC-04-AA
- Technical Support
- Index