Greenheck Microprocessor Controller (475595 IOM) TAP v2.10 April 2014 (RVE, ERCH-01, ERT-01) - Manual (Page 26)

T
HIS SCREEN ALLOWS THE USER TO ADJUST
BAC
NET
IP
PARAMETERS
.
This screen only appears if the selected BMS protocol is set to BACnet IP/Eth and
BACnet Plugin = YES.
If a BACnet IP card has been installed, the default parameters can be changed
via the controller display. The card is in DHCP mode from the factory. Once
communication is established, the user can enter static IP parameters.
To view current parameters:
1. Power on controller and allow several minutes to initialize.
2. Go to BMS Config menu and view BACnet Read/Write screen.
3. Change Function to Read and Update? to YES.
TCP/IP SETUP
Instance: 77000
IP set by: DHCP
IP: 128.2.104.134
Subnet: 255.255.000.000
Gatewy: 128.2.0.12
TCP/IP SETUP
DNS 1: 193.168.001.001
DNS 2: 193.168.001.001
Type: IP
T HIS SCREEN ALLOWS THE USER TO ADJUST BAC NET MSTP PARAMETERS .
This screen only appears if the selected BMS protocol is set to BACnet MSTP and
BACnet Plugin = YES.
If a BACnet MSTP card has been installed, the default parameters can be
changed via the controller display. Factory settings are shown in the screen to the
left.
To view current parameters:
1. Power on controller and allow several minutes to initialize.
2. Go to BMS Config menu and view BACnet Read/Write screen.
3. Change Function to Read and Update? to YES.
Current BACnet MSTP parameters should now be displayed in the BACnet MSTP
SETUP screen. If all values appear to be zeros, consult the factory. (Make sure
you have allowed several minutes for the controller to initialize). *Values may
appear to be zero prior to setting the Function to READ.
To change BACnet MSTP parameters:
1. Power on controller and allow several minutes to initialize.
2. Go to BMS Config menu and view MSTP SETUP screen.
3. Move cursor to desired parameter by pressing the
buttons. Press
to select the parameter to change. Press the buttons to adjust the
parameter. Press to save adjusted value.
4. Once desired parameters have been entered, go to BACnet Read/Write
screen. Change Function to Write and Update? to YES.
5. Reboot the controller by cycling power to the unit. Allow several minutes for
the controller to initialize.
6. View MSTP parameters. If changed values did not save, contact the factory.
MSTP SETUP
Instance: 77000
Baudrate 38400
MAC Addr:
0
MaxMasters: 127
MaxInfoFrames: 20
BACnet Read/Write
Function: Read
Update? Yes
*Cycle unit power to confirm
write command.
T
HIS SCREEN ALLOWS THE USER TO ADJUST
M
ODBUS PARAMETERS
.
This screen only appears if the selected BMS protocol is set to Modbus .
The address is the Modbus address of the card installed in the SERIAL CARD
port located on the face of the controller. (Factory Default Address = 1).
MODBUS SETUP
Address: 1
Baudrate 9600
Stop bit: 2
Parity mode: NONE
T
HIS SCREEN ALLOWS THE USER TO SELECT THE
BMS
PROTOCOL
. A
LL
BMS
PROTOCOLS REQUIRE A COMMUNICATIONS CARD INSTALLED IN THE
SERIAL CARD
PORT , LOCATED ON THE FACE OF THE CONTROLLER .
If the protocol is BACnet MSTP or BACnet IP/Eth, the user can change common
BACnet parameters via the controller. The BACnet Plugin must be set to YES.
BMS Configuration
Protocol: BACnet MSTP
BACnet Plugin? YES
The BMS Config menu allows the user to view and alter BMS protocol settings.
If the BMS protocol is BACnet or Modbus, additional screens allow further
configuration. See below for details. To access the BMS Config sub-menu, enter
the service password (Default=1000).
G. Service
c. BMS Config
26 DDC Controller for Tempered Air Products
®