beautypg.com
FAD-40 Technical Manual, Rev. 1.06 December 2012
Page 2 of 52
Table of Contents:
1.
SAFETY INSTRUCTIONS ........................................................................................................................... 4
2.
DECLARATION OF CONFORMITY ........................................................................................................... 5
3.
INTRODUCTION ......................................................................................................................................... 6
3.1.
Overview ...................................................................................................................................................... 6
3.2.
Key features and Specifications .................................................................................................................. 7
3.3.
Housing ........................................................................................................................................................ 9
3.4.
Accessories .................................................................................................................................................. 9
4.
INSTALLATION......................................................................................................................................... 10
4.1.
Recommendations ..................................................................................................................................... 10
4.1.1.
Control Cabinet Design ................................................................................................................................ 10
4.1.2.
Cabling ......................................................................................................................................................... 10
4.1.3.
Mechanical Installation ................................................................................................................................. 10
4.2.
Electrical Connections ............................................................................................................................... 10
4.2.1.
Power Supply and Grounding ...................................................................................................................... 10
4.2.2.
Load Cell Connection ................................................................................................................................... 11
4.2.3.
Digital I/O Connection .................................................................................................................................. 11
4.2.4.
Communication Interface ............................................................................................................................. 12
4.3.
Commissioning .......................................................................................................................................... 12
5.
SETUP ....................................................................................................................................................... 13
5.1.
Installation of the xFace Software.............................................................................................................. 13
5.2.
Connection to the xFace Software............................................................................................................. 13
5.3.
A/D Converter Setup and Calibration ........................................................................................................ 14
5.3.1.
Scale Parameters ........................................................................................................................................ 14
5.3.2.
RS-485 Serial Interface Setup ..................................................................................................................... 15
5.3.3.
Scale Build and Calibration .......................................................................................................................... 16
5.4.
A/D Converter Performance Test .............................................................................................................. 18
5.5.
Setup of Digital I/O ..................................................................................................................................... 18
5.6.
Bus Interface Setup ................................................................................................................................... 20
5.7.
Bus Addressing via Setup Switch .............................................................................................................. 20
5.8.
Back up Settings and Calibration Data ...................................................................................................... 20
5.9.
BSI Data Structure (for FAD-40 and FAD-40MB only) .............................................................................. 21
5.10.
Modbus Data Structure (for FAD-40MB and FAD-40EN only) .............................................................. 25
5.11.
Profibus and ProfiNet Data Structure (for FAD-40Px only) .................................................................... 28
5.12.
CANopen Data Structure (for FAD-40CO only) ..................................................................................... 32
6.
FAD-40 / FAD-40MB
– WITH RS-485 INTERFACE ................................................................................. 36
6.1.
Front View .................................................................................................................................................. 36
6.2.
Electrical Connections ............................................................................................................................... 37
6.3.
Interfacing .................................................................................................................................................. 37
6.4.
Setup and Calibration ................................................................................................................................ 37
6.5.
Modbus RTU (for FAD-40MB only)............................................................................................................ 37
7.
FAD-40PB
– WITH PROFIBUS INTERFACE ........................................................................................... 38
7.1.
Front View .................................................................................................................................................. 38
7.2.
Electrical Connections ............................................................................................................................... 39
7.3.
Interfacing .................................................................................................................................................. 40
7.4.
Setup and Calibration ................................................................................................................................ 40
7.5.
Profibus Setup ........................................................................................................................................... 40
8.
FAD-40PN
– WITH PROFINET INTERFACE ........................................................................................... 41
8.1.
Front View .................................................................................................................................................. 41
8.2.
Electrical Connections ............................................................................................................................... 42
8.3.
Interfacing .................................................................................................................................................. 43
8.4.
Setup and Calibration ................................................................................................................................ 43
8.5.
ProfiNet Setup............................................................................................................................................ 43
9.
FAD-40EN
– WITH ETHERNET INTERFACE .......................................................................................... 44
9.1.
Front View .................................................................................................................................................. 44
9.2.
Electrical Connections ............................................................................................................................... 45
9.3.
Interfacing .................................................................................................................................................. 46
9.4.
Setup and Calibration ................................................................................................................................ 46
9.5.
Ethernet Setup ........................................................................................................................................... 46
