Kenwood TS-850S - Manual (Page 41)

Note
When the RIT is ON the transmit frequency may
be different from the receive frequency. For normal
operation leave the RIT switch OFF. It should be
used only when necessary.
4-10-14. XIT control
Transmitter Incremental Tuning is very similar to
RIT. XIT is only active in the transmit mode. By
using the XIT function it is possible to offset the
transmit frequency without the normal loss of
receiver audio that is experienced when using the
SPLIT function. The XIT step size is either 10 Hz or
20 Hz. (Please refer to Section 4-10-15.)
Offsets of ±1.2 kHz are possible.
The RIT/XIT offset can be preset, without affecting
the actual operating frequency by turning OFF the
RIT/XIT and using the RIT/XIT display to determine
the offset.
4-10-15. Power on function selection
Several of the functions of this transceiver can be
changed at the time the transceiver is turned ON.
Repeat to release each function.
1. Press and hold the LSB/USB key while you turn
on the POWER switch.
2. A number will appear in the display.
3. Select the desired number by rotating the M.CH/
VFO CH control.
4. Change the function by pressing the UP/DOWN
switch.
5. Function selection can be turned off by pressing the
CLR key, or by pressing the POWER switch OFF and
back ON.
No. Programmable functions Initial state
00 Beep tones: ON/OFF ON
01
Audible mode announcement:
ON(Morse code)/OFF(Beep
tones)
ON
02
Audible alarm:
ON(Morse code)/OFF(Beep
tones)
ON
03
M.CH/VFO CH control step
frequency selection:
10 kHz/5 kHz/1 kHz
10 kHz
04
M.CH/VFO CH control step
frequency selection:
10 kHz/9 kHz (AM mode only)
10 kHz
05
TUNING knob step frequency
selection: 100 Hz/10 Hz (AM
and FM mode only) (Except the
FINE function is ON.)
100 Hz
No. Programmable functions Initial state
06
UP/DOWN switch step
frequency selection:
1000 kHz/500 kHz/1 kHz
(When 1 MHz key is ON.)
1000 kHz
07
10 Hz display resolution:
ON/OFF
ON
08 SSB AUTO mode shift: ON/OFF ON
09 Meter peak hold: ON/OFF OFF
10
Automatically increments the
memory channel data time each
time you enter a frequency into
memory.
OFF
11
FSK transmission key short:
OFF(SPACE)/ON(MARK)
OFF
12
The shift range of the FSK mode
can be set to 170, 200, 425, or
850 Hz by using the UP/DOWN
switch.
170 Hz
13
You can switch between FSK
mode receive tones high (2125
Hz) and low (1275 Hz).
2125 Hz
14 Program scan hold: ON/OFF OFF
15
Storing the band frequency
before the UP/DOWN switch is
pressed : Required(ON)/Not
required(OFF)
ON
16
Determine whether to change
the frequency with the tuning
knob (ON) or not (OFF) when
the standard memory channel is
recalled to RX VFO.
OFF
17
RIT/XIT variable range:
1.27 kHz/2.54 kHz
1.27 kHz
18 Select the sub tones 88.5 Hz
19
Sub tones:
b(Tone burst)/c(Continuous
tones)
c
20
Antenna Tuner:
ON(AUTO)/OFF(MANUAL)
(When the SW1 switch is INT.)
ON
21
Auto weight function : ON/OFF
(When the ELECTRONIC KEY
switch is ON.)
ON
22
Reverse mode: ON/OFF
(When Auto weight function is
ON.)
OFF
35