Carl Goldberg GBGA0055 - Manual (Page 13)

13
THE INSTRUCTIONS WILL LEAD YOU THROUGH THE
ASSEMBLY SEQUENCE, OCCASIONALLY SENDING YOU
BACK TO REPEAT STEPS. CAREFULLY READ EACH STEP
BEFORE YOU PROCEED TO DO THE INSTRUCTION.
1. Find all the parts that you will need to build the wing.
THEY INCLUDE:
(4) 3/8" SQ. X 35" SPAR BASS (MIL #4528)
(2) SHAPED L.E BALSA (MIL #4524)
(2) NOTCHED T.E BALSA (MIL #4523)
(2) WING RIBS 2 & 8 BALSA (D.C. 5310-3325)
(2) WING RIBS 3 & 6 BALSA (D.C. 5511-3326)
(2) WING RIBS 4 & 1 BALSA (D.C. 5512-3327)
(2) WING RIBS 5 & 7 BALSA (D.C. 5513-3328)
(2) WING RIBS 1, 9 & 10 BALSA (D.C. 5514-3329)
(4) WING CENTER SHEETING BALSA
(D.C. 5515-3330)
(2) SHEAR-WEBS BALSA (D.C. 5520-3332)
(2) WING JOINER PLY
(2) BELCRANK PLATFORMS PLY
(D.C. 5516-3483)
(2) DOWEL SUPPORT PLY (D.C. 5516-3483)
(1) WING SUPPORT FRT PLY (D.C. 5516-3483)
(1) WING SUPPORT REAR PLY (D.C. 5516-3483)
(1) WING SUPPORT TIP PLY (D.C. 5516-3483)
(1) SERVO PLATFORM PLY (D.C. 5516-3483)
(1) DOWEL GUIDE PLY (D.C. 5509-3480)
(2) INBOARD T.E. BALSA (MIL #4526)
(5) 1/16" x 1/4" x 24" CAPS BALSA (STK #4525)
(2) AILERONS BALSA (MIL #4527)
(6) 1/16" x 2-3/4" x 35" BALSA (SHT #4888)
(4) 1/16" x 2-1/2" x 35" BALSA (SHT#4887)
(1) 3/4" x 33" NYLON FABRIC (NYL #5210)
(1) 5/16" x 4-3/4" DOWEL BIRCH (MIL #1759)
(2) .063" x 20-3/4" AILERON WIRE (MTL #1230)
(2) .063" x 7" THREADED ROD (MTL #1270)
(2) AILERON BELCRANKS (NYL #1410)
(2) AILERON BUSHINGS (MTL #1182)
(2) 2-56 NUT (MTL #1115)
(2) 2-56 x 1/2" MACHINE SCREW (MTL #1041)
(2) #2 WASHER (NYL#1461)
(4) NYLON SNAP-NUT (NYL #1138)
(3) 1/16" I.D. x 1" BRASS TUBE (BRS #1376)
(1) AILERON COUPLER BLOCK (NYL #1427)
(1) 2-56 x 3/4" MACHINE SCREW (MTL #1042)
(1) 2-56 x 1/8" MACHINE SCREW (MIL #1040)
(1) SNAP LINK (NYL #1405)
(8) FLEX POINT HINGES (NYL #1449)
(1) C.G. CENTERLINE TOOL (NYL #1425)
CONSTRUCTING THE WING (35 Steps)