Holtgreven GSE-375 - Manual (Page 63)

57
Parameter
Setting Displayed
Name
Description
Type/choices
(*=Default)
line must be connected between the COMM Ports of the master and
remote unit. If this parameter is disabled the [SELECT] key will have
no effect on the master unit.
P283.01 Prtut
Enables or disables the use of the [PRINT] and [UNITS] keys on the
master unit (350 or 370). When this parameter is enabled and the
keys are pressed, the [PRINT] and [UNITS] keys will be simulated.
The Tx, Rx and GND line must be connected between the COMM
Ports of the master and remote unit. If this parameter is disabled the
keys will have no effect on the master unit.
Enable* /
Disable
P284.01 Print
Enables or disables the use of the [PRINT] key on the master unit.
When this parameter is enabled and the key is pressed, a [PRINT]
key command will be recognized by the master unit. The Tx, Rx and
GND line must be connected between the COMM Ports of the master
and remote unit. If this parameter is disabled the [PRINT] key will
have no effect on the master unit.
Enable* /
Disable
P285.01 Tare
Enables or disables the use of the [TARE] key on the master unit.
When this parameter is enabled and the key is pressed, a [TARE] key
command will be recognized by the master unit. The Tx, Rx and GND
line must be connected between the COMM Ports of the master and
remote unit. If this parameter is disabled the [TARE] key will have no
effect on the master unit.
Enable* /
Disable
P286.01 Enter
Enables or disables the use of the [SAMPLE/Enter] key on the master
unit. When this parameter is enabled and the key is pressed, an
[SAMPLE/Enter] key command will be recognized by the master unit.
The Tx, Rx and GND line must be connected between the COMM
Ports of the master and remote unit. If this parameter is disabled the
[SAMPLE/Enter] key will have no effect on the master unit.
Enable* /
Disable
P287.01 Clear
Enables or disables the use of the [CLR] key on the master unit.
When this parameter is enabled and the key is pressed, a [CLR] key
command will be recognized by the master unit. The Tx, Rx and GND
line must be connected between the COMM Ports of the master and
remote unit. If this parameter is disabled the [CLR] key will have no
effect on the master unit.
Enable* /
Disable
P288.01 Digit
Enables or disables the use of the numeric keys on the master unit
including the decimal key. When this parameter is enabled and a
numeric key is pressed, it will be recognized by the master unit. The
Tx, Rx and GND line must be connected between the COMM Ports of
the master and remote unit. If this parameter is disabled the numeric
keys will have no effect on the master unit.
Enable* /
Disable
P289.01 Target
Enables or disables the use of the [TARGET] key on the master unit.
When this parameter is enabled and the key is pressed, a target key
command will be recognized by the master unit. The Tx, Rx and GND
line must be connected between the COMM Ports of the master and
remote unit. If this parameter is disabled the [TARGET] key will have
no effect on the master unit. Model 355 only.
Enable* /
Disable
Custom (P271)
When set for Custom, the master unit will send customized information to be displayed on the
remote unit. A parameter or text data may be transmitted to the remote unit on a continual or "on
demand" basis.
Set P271 for Custom and set all other remote display parameters (refer to Table 3-15). Configure
the parameters in the master unit (refer to Setup Master Unit on page 55). Make sure that the
wiring connections between the master and remote units are correct (refer to Remote Display
Connections on page 5. Follow the instructions below for configuring the master unit.
1. Turn echo off at P290.
2. Set the transmit to be continuous at P210 (port 1) or P230 (port 2). This is the port going to
the remote unit.
3. Program custom transmit in the master unit at P1000 (port 1) or P2000 (port 2). See the
example below for instructions on programming a custom transmit.