Elecraft KX3 Programmers Reference - Manual (Page 17)

17
Table 6 KX3 MN values. These are the same as the K3’s only if the two are functionally identical.
nnn is permanently associated with a menu entry, even if entries are moved.
‡ = can be read/set using MP command (or MQ in the case of TXCRNUL). In many cases the get/set value
requires interpretation, or must be bit-masked to isolate the relevant field. See MP command for details.
Entry nnn Entry nnn Entry nnn Entry nnn
ALARM ‡ 000 040 080 CW KEY1 ‡ 120
CW IAMB ‡ 001 041 081 CW KEY2 ‡ 121
002 042 MIC BTN ‡ 082 VOX INH ‡ 122
003 043 083 RX I/Q ‡ 123
004 044 VFO CTS ‡ 084 RX ISO ‡ 124
MSG RPT ‡ 005 AUTOINF ‡ 045 085 RXSBNUL ‡ 125
006 046 086 AM MODE ‡ 126
RPT OFS ‡ 007 AF LIM ‡ 047 VFO OFS ‡ 087 TXSBNUL ‡ 127
RX EQ 008 048 WATTMTR ‡ 088 AGC MD ‡ 128
TX EQ 009 049 XVx ON 089 AGC SPD ‡ 129
VOX GN ‡ 010 050 XVx RF 090 TX BIAS 130
011 051 XVx IF 091 TX GAIN 131
CW WGHT ‡ 012 LCD TST 052 XVx PWR 092 TXCRNUL ‡ 132
2 TONE 013 053 XVx OFS 093 AUTOOFF ‡ 133
014 054 XVx ADR 094 RX XFIL ‡ 134
015 055 095 MICBIAS ‡ 135
016 056 TX ESSB ‡ 096 PREAMP ‡ 136
017 RS232 057 097 BAT CHG ‡ 137
FM MODE ‡ 018 TUN PWR ‡ 058 098 BKLIGHT ‡ 138
019 059 099 COR LVL ‡ 139
020 SMTR MD ‡ 060 100 DUAL RX ‡ 140
FM DEV ‡ 021 061 TX GATE ‡ 101 ACC2 IO ‡ 141
022 REF CAL 062 102 RX SHFT ‡ 142
ATU MD ‡ 023 063 103 RX NR ‡ 143
BAT MIN ‡ 024 064 VFO CRS ‡ 104 PBT SSB ‡ 144
025 065 AFX MD ‡ 105 LED BRT ‡ 145
SER NUM 026 066 106 PA MODE ‡ 146
027 067 107 2M MODE ‡ 147
FW REVS 028 068 108 148
029 069 109 149
030 SW TEST 070 MACRO x 110 150
031 SW TONE ‡ 071 111
032 TECH MD ‡ 072 112
033 TIME 073 113
034 AGC THR ‡ 074 114
035 075 115
036 BND MAP ‡ 076 116
037 077 117
038 078 118
039 079 VFO NR ‡ 119 Exit Menu 255