beautypg.com

Prescolite ARCHITRAK SYSTEM AKTW12, AKTW24, AKTW36, AKTW48 Track Wand User Manual

Instruction sheet, Installation instructions architrak, System

background image

Instruction

Sheet

www

.prescolite.com

• Prescolite

TollFree

Technical Support

1.888.PRS.4TEC

• Hours: 8am - 5pm ET

101 Corporate Drive • Spartanburg, SC 29303

With representatives offices in principal cities throughout North America.

Copyright 2005, 08/05 revision, All Rights Reserved - Printed in U.S.A.

Part No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .157730100

Instruction

Sheet

INSTALLATION INSTRUCTIONS

OR AKTW12, AKTW18, AKTW24, AKTW36, AKTW48 TRACK WAND.
FOR USE WITH PRESCOLITE AKT ONE/TWO CIRCUIT TRACK SYSTEM ONLY
READ INSTALLATION INSTRUCTIONS BEFORE INSTALLING TRACK SYSTEM
SAVE INSTRUCTIONS FOR REFERENCE WHEN MAKING ADDITIONS TO OR CHANGES IN THE TRACK SYSTEM.

INSTALLATION

1. Refer to PRECOLITE AKT series track for track installation instructions.

2. Insert contact head into prescolite akt track rail. Twist contact head 1/4 turn (90 degrees) until locking tabs snap up into place. To

remove wand from track. Retract locking tabs turn 1/4 turn (90 degrees) and remove.

3. To install fixture assembly into wand fixture receptacle follow step 2 above. Also refer to instructions provided with fixture assemblies.

4. When track is wired for single circuit operation. Be sure wand engages energized circuit.

WARNING:

SHOULD WAND BECOME DAMAGED IN ANY WAY

SHUT OFF POWER TO TRACK SYSTEM, REMOVE

WAND IMMEDIATELY.

AKT TRACK RAIL

PULL DOWN PLASTIC COVER

TO REMOVE WAND FROM

TRACK RAIL

LOCKING TAB

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information

and instructions concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials,

and proper lamping. Do not install in areas subject to combustible vapors or gases. Before wiring to power supply and

during servicing or relamping, turn off power at fuse or circuit breaker. All servicing or relamping must be performed by

qualified service personnel. Product must be grounded to avoid potential electric shock or other potential hazard.

Product must be mounted in locations and at heights and in a manner consistent with its intended use, and in

compliance with the National Electrical Code and local codes. The use of accessory equipment not recommended by

the manufacturer or installed contrary to instructions may cause an unsafe condition. Do not block light emanating from

product in whole or part, as this may cause an unsafe condition. Do not allow items such as drapes, curtains, screens or

the like to come into contact with the product or to block light from the product, as this may cause an unsafe condition.

INSTALLATION INSTRUCTIONS

ARCHITRAK

®

SYSTEM

CONTACT HEAD

WAND FIXTURE RECEPTACLE

WAND ASSEMBLY

WARNING:

WHEN INSTALLING OR USING THIS TRACK SYSTEM, BASIC SAFETY

PRECAUTIONS SHOULD ALWAYS BE FOLLOWED. READ ALL INSTRUCTIONS.

DO NOT INSTALL THIS TRACK IN DAMP OR WET LOCATIONS. DO NOT

INSTALL ANY PART OF TRACK SYSTEM LESS THAN 5 FEET ABOVE FLOOR.

DO NOT INSTALL ANY FIXTURE ASSEMBLY CLOSER THAN 6 INCHES

FROM ANY CURTAIN, OR SIMILAR COMBUSTIBLE MATERIAL. DISCONNECT

ELECTRICAL POWER BEFORE ADDING TO OR CHANGING THE CONFIGURATION

OF THE TRACK. DO NOT ATTEMPT TO ENERGIZE ANYTHING OTHER THAN

LIGHTING TRACK FIXTURES ON THE TRACK TO REDUCE THE RISK OF

FIRE AND ELECTRIC SHOCK, DO NOT ATTEMPT TO CONNECT POWER

TOOLS, EXTENSION CORDS, APPLIANCES, AND THE LIKE TO THE TRACK.