Prescolite ARCHITRAK SYSTEM AKTCSK - Canopy Mount Stem Kit - Manual

Instruction
Sheet
www
.prescolite.com
• Prescolite
TollFree
Technical Support
1.888.PRS.4TEC
• Hours: 8am - 5pm ET
101 Corporate Drive • Spartanburg, SC 29303
With representatives offices in principal cities throughout North America.
Copyright 2005, 08/05 revision, All Rights Reserved - Printed in U.S.A.
Part No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .157770100
Instruction
Sheet
INSTALLATION INSTRUCTIONS
FOR AKTCSK TRACK STEM KITS
FOR USE WITH PRESCOLITE AKT ONE/TWO CIRCUIT TRACK SYSTEM ONLY.
READ INSTALLATION INSTRUCTIONS BEFORE INSTALLING THE TRACK SYSTEM
SAVE INSTRUCTIONS FOR REFERENCE WHEN MAKING ADDITIONS TO OR CHANGES IN THE TRACK SYSTEM.
INSTALLATION
1. Refer to PRESCOLITE AKT series track for track installation instructions
2. Assemble stem to universal cross bar with two lock nuts. Mount cross bar to ceiling box with screws provided with ceiling box.
Slide 4-1/2” square canopy up stem. Secure to universal cross bar with two flat head screws.
3. Assemble z bracket to track rail with screws provided through slots provided at ends or middle of track.
4. Slide plastic cover up stem. Secure stem to z bracket with two lock nuts provided. Slide cover down over z bracket assembly.
WHEN STEM KIT IS USED AS A POWER FEED YOU MUST USE A AKTCSK WH OR AKTCSK BL TRACK STEM WIRE COVER.
INSTALL AS FOLLOWS.
1. Run suitable black, white, green code gauge wire through stem. Be sure to allow at least 10” of wire for wiring to connector.
See wiring instructions provided with connectors AKTEF, AKTT, AKTSL
2. Connect black stem wire to hot wire usually black. White to white neutral. Green to green or bare copper ground wire. Use
approved connectors (wirenuts).
3. Disgard plastic stem cover, replace with stem wire cover.
4. See notes 1, 2, 3, 4 and diagram below for stem assembly.
Z BRACKET MOUNTING SCREW
Z BRACKET
IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information
and instructions concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials,
and proper lamping. Do not install in areas subject to combustible vapors or gases. Before wiring to power supply and
during servicing or relamping, turn off power at fuse or circuit breaker. All servicing or relamping must be performed by
qualified service personnel. Product must be grounded to avoid potential electric shock or other potential hazard.
Product must be mounted in locations and at heights and in a manner consistent with its intended use, and in
compliance with the National Electrical Code and local codes. The use of accessory equipment not recommended by
the manufacturer or installed contrary to instructions may cause an unsafe condition. Do not block light emanating from
product in whole or part, as this may cause an unsafe condition. Do not allow items such as drapes, curtains, screens or
the like to come into contact with the product or to block light from the product, as this may cause an unsafe condition.
INSTALLATION INSTRUCTIONS
ARCHITRAK
®
SYSTEM
FLAT HEAD SCREWS
PROVIDED
NOTE: WIRING IS PRESENT
WHEN USED AS A POWER FEED
ONLY.
WARNING:
WHEN INSTALLING OR USING THIS TRACK SYSTEM, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED. READ ALL INSTRUCTIONS.
DO NOT INSTALL THIS TRACK IN DAMP OR WET LOCATIONS. DO NOT INSTALL
ANY PART OF TRACK SYSTEM LESS THAN 5 FEET ABOVE FLOOR. DO NOT
INSTALL ANY FIXTURE ASSEMBLY CLOSER THAN 6 INCHES FROM ANY
CURTAIN, OR SIMILAR COMBUSTIBLE MATERIAL. DISCONNECT ELECTRICAL
POWER BEFORE ADDING TO OR CHANGING THE CONFIGURATION OF THE
TRACK. DO NOT ATTEMPT TO ENERGIZE ANYTHING OTHER THAN LIGHTING
TRACK FIXTURES ON THE TRACK TO REDUCE THE RISK OF FIRE AND
ELECTRIC SHOCK, DO NOT ATTEMPT TO CONNECT POWER TOOLS,
EXTENSION CORDS, APPLIANCES, AND THE LIKE TO THE TRACK SYSTEM.
PRESCOLITE AKT RAIL
LOCKNUT 4 PER STEM
STEM
COVER
UNIVERSAL CROSS BAR
CANOPY
WIRE WIRENUTS
NOT FURNISHED
3-1/2” CEILING BOX
NOT FURNISHED
5”